Vol 5, No 1 (2016)

Chief Editor

Muhamad Fitri ST, M.Si, Ph. D, Universitas Mercu Buana, Indonesia

Editorial Board

Prof. Dr. Ir. Chandrasa Soekardi, Universitas Mercu Buana, Indonesia
Dr. Kontan Tarigan, Universitas Mercu Buana, Indonesia
Dr. Nurdin Ali, Universitas Syiah Kuala, Indonesia
Dr. Poempida Hidayatulloh, Universitas Mercu Buana, Indonesia
Prof. Dr. Bambang Suharno, Universitas Indonesia, Indonesia
Dr.-Ing. Pudji Untoro, Universitas Surya, Indonesia
Dr.-Ing. Ir. Kusnanto Kusnanto, Universitas Gadjah Mada, Indonesia
Dr. Sagir Alva, Universitas Mercu Buana, Indonesia
Dr. Abdul Hamid, Universitas Mercu Buana

Editorial Staff

Bakri Rio Rahayu, Universitas Mercu Buana, Indonesia
Yananto Mihadi Putra, Universitas Mercu Buana, Indonesia
Goffari Maulana, Universitas Mercu Buana, Indonesia

Managing Editor

Ir. Haris Wahyudi, M.Sc, Universitas Mercu Buana, Indonesia
Muhamad Fitri, ST, MSi, PhD. Universitas Mercu Buana, Indonesia

Notifications

Journal Content
Browse

Keywords Age Replacement,downtime, optimal perencanaan perawatan dan preventive maintenance Airfoil, Qblade, Turbin Angin, Daya Barcode id, PLC, Raspberry Pi, PLC with Barcode Integration COP Co-firing, Boiler Pulverizer Coal, Sawdust, Emisi gas buang Composite fibers, weaving pattern, reinforcement, mechanical test, ballistic test Efisiensi Kata kunci: exhaust gas temperature margin, air mode, high pressure compressor clearance control Kendaraan listrik, baterai, service life, pengisian baterai, pengosongan baterai. Kursi Plastik MRT Jakarta Panel Surya Programable Logic Controller (PLC), Infrared Refrigeran, ODP, GWP, R22 Safety Factor Schedule Oil Sampling, Sistem Pelumasan, Diesel Engine, FMEA Shaft,Material,CAD egg incubator, tenaga surya, photovoltaic, unggas emergency landing loads fiber diameter, morphology, mechanical characteristics, tensile strength, Young’s modulus floor support structure

Aims and Scope
Peer Review Policy
Author Guidelines
Editorial Board
Abstracting & Indexing
Publication Ethics
Open Access Statement
Plagiarism Policy
Copyright and License
Article Processing Charge
Contact Us

Language

User

Font Size

Current Issue

Vol 5, No 1 (2016)

Table of Contents

Articles

ANALISA KERUSAKAN PADA FORKLIFT ELEKTRIK NICHIYU FB20-75C DENGAN METODE FMEA

10.22441/jtm.v5i1.703

Heri Suwandono

1-6

ANALISA LAJU KOROSI PADA PUMP IMPELLER DI INDUSTRI PERTAMBANGAN BATU BARA

10.22441/jtm.v5i1.704

Puguh Ogi Nur Rachman

7-13

ANALISA PEMANFAATAN EXCESS COKE OVEN GAS SEBAGAI BAHAN BAKAR GAS HEATER DI IRON MAKING

10.22441/jtm.v5i1.705

Edi Suderajat

14-18

OPTIMASI FILLING TIME INJECTION MOLDING CRISPER DENGAN BANTUAN SOFTWARE AUTODESK MOLDFLOW INSIGHT

10.22441/jtm.v5i1.706

Raswan Rudiyadi

19-22

OPTIMASI PERHITUNGAN ULANG KEBUTUHAN LIFT PENUMPANG TYPE IRIS1-NV PA 20 (1350) CO105 PADA GEDUNG APARTEMEN 17 LANTAI

10.22441/jtm.v5i1.707

Andri Sulistyo

23-30

PEMANFAATAN LIMBAH LUMPUR (SLUDGE) WASTEWATER TREATMENT PLANT PT.X SEBAGAI BAHAN BAKU KOMPOS

10.22441/jtm.v5i1.708

Dicky Cahyadhi

31-36

Jurnal Teknik Mesin (JTM)
Program Studi Teknik Mesin, Fakultas Teknik, Universitas Mercu Buana
Jl. Meruya Selatan No. 01, Kembangan, Jakarta Barat 11650, Indonesia
Email: [email protected]
Telp.: 021-5840815/ 021-5840816 (Hunting)
Fax.: 021-5871335

JTM is indexed by the following abstracting and indexing services:

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.