Vol 4, No 3 (2015)

Chief Editor

Muhamad Fitri ST, M.Si, Ph. D, Universitas Mercu Buana, Indonesia

Editorial Board

Prof. Dr. Ir. Chandrasa Soekardi, Universitas Mercu Buana, Indonesia
Dr. Kontan Tarigan, Universitas Mercu Buana, Indonesia
Dr. Nurdin Ali, Universitas Syiah Kuala, Indonesia
Dr. Poempida Hidayatulloh, Universitas Mercu Buana, Indonesia
Prof. Dr. Bambang Suharno, Universitas Indonesia, Indonesia
Dr.-Ing. Pudji Untoro, Universitas Surya, Indonesia
Dr.-Ing. Ir. Kusnanto Kusnanto, Universitas Gadjah Mada, Indonesia
Dr. Sagir Alva, Universitas Mercu Buana, Indonesia
Dr. Abdul Hamid, Universitas Mercu Buana

Editorial Staff

Bakri Rio Rahayu, Universitas Mercu Buana, Indonesia
Yananto Mihadi Putra, Universitas Mercu Buana, Indonesia
Goffari Maulana, Universitas Mercu Buana, Indonesia

Managing Editor

Ir. Haris Wahyudi, M.Sc, Universitas Mercu Buana, Indonesia
Muhamad Fitri, ST, MSi, PhD. Universitas Mercu Buana, Indonesia

Notifications

Journal Content
Browse

Keywords Age Replacement,downtime, optimal perencanaan perawatan dan preventive maintenance Airfoil, Qblade, Turbin Angin, Daya Barcode id, PLC, Raspberry Pi, PLC with Barcode Integration COP Co-firing, Boiler Pulverizer Coal, Sawdust, Emisi gas buang Composite fibers, weaving pattern, reinforcement, mechanical test, ballistic test Efisiensi Kata kunci: exhaust gas temperature margin, air mode, high pressure compressor clearance control Kendaraan listrik, baterai, service life, pengisian baterai, pengosongan baterai. Kursi Plastik MRT Jakarta Panel Surya Programable Logic Controller (PLC), Infrared Refrigeran, ODP, GWP, R22 Safety Factor Schedule Oil Sampling, Sistem Pelumasan, Diesel Engine, FMEA Shaft,Material,CAD egg incubator, tenaga surya, photovoltaic, unggas emergency landing loads fiber diameter, morphology, mechanical characteristics, tensile strength, Young’s modulus floor support structure

Aims and Scope
Peer Review Policy
Author Guidelines
Editorial Board
Abstracting & Indexing
Publication Ethics
Open Access Statement
Plagiarism Policy
Copyright and License
Article Processing Charge
Contact Us

Language

User

Font Size

Current Issue

Vol 4, No 3 (2015)

Table of Contents

Articles

ANALISIS PENGARUH PERLAKUAN PANAS TERHADAP KEKERASAN DAN STUKTUR MIKRO MATERIAL S45C DAN SS400 YANG DIGUNAKAN SEBAGAI ALAT POTONG KULIT SEPATU

10.22441/jtm.v4i3.1268

Hadi Wardoyo

67-72

ANALISA PENGARUH CAMPURAN BAHAN COMPOUND EPDM RECLAIM UNTUK PEMBUATAN COVER RELAY TERHADAP SIFAT MEKANIK

10.22441/jtm.v4i3.1273

Mukhamad Bayu Fikri

73-80

PENGARUH INJECTION TIME DAN BACKPRESSURE TERHADAP CACAT PENYUSUTAN PADA PRODUK KEMASAN TOPLES DENGAN INJECTION MOLDING MENGGUNAKAN MATERIAL POLISTYRENE

10.22441/jtm.v4i3.1269

U. Wahyudi

81-90

ANALISA PENGARUH HEAT TREATMENT MATERIAL CARBIDE DRILL ROD AF1 TERHADAP KINERJA PROSES PUNCH

10.22441/jtm.v4i3.1270

Giging Herdiana

91-93

ANALISIS PENGARUH VARIASI CDI TERHADAP PERFORMA DAN KONSUMSI BAHAN BAKAR HONDA VARIO 110cc

10.22441/jtm.v4i3.1271

Sachrul Ramdani

94-98

ANALISIS PERBANDINGAN EVAPORATOR KULKAS (LEMARI ES) DENGAN MENGUNAKAN REFRIGERANT R-22 DAN R-134A

10.22441/jtm.v4i3.1272

Imam Faozan

99-105

Jurnal Teknik Mesin (JTM)
Program Studi Teknik Mesin, Fakultas Teknik, Universitas Mercu Buana
Jl. Meruya Selatan No. 01, Kembangan, Jakarta Barat 11650, Indonesia
Email: [email protected]
Telp.: 021-5840815/ 021-5840816 (Hunting)
Fax.: 021-5871335

JTM is indexed by the following abstracting and indexing services:

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.