Prototipe Alat Ukur Ketinggian Coil Block Pada Kereta Kerja Kereta Cepat Indonesia China
DOI:
https://doi.org/10.22441/jte.2025.v16i3.010Abstract
Pembuatan desain prototipe alat ukur ketinggian Coil Block Track Circuit Reader pada Kereta Kerja KCIC dilakukan secara konvensional dengan mengukur secara manual dari permukaan rel mengunakan mistar. Pencahayaan yang didapat tidak maksimal karena coil blok track circuit reader berada di underfloor sehingga menyulitkan dalam pengukuran. Hal ini memungkinkan kurangnya tingkat keselamatan, kepraktisan pencatatan dan akurasi hasil pengukuran. Tujuan dari penelitian ini adalah membuat prototipe alat ukur ketinggian track circuit reader untuk meningkatkan akurasi dan keselamatan petugas. Metode yang dilakukan ini berdasarkan perancangan dan pembuatan alat. Hasil pengukuran penyimpangan Prototipe Alat ukur ketinggian Coil Block Track Circuit Reader yang dilakukan oleh 4 orang adalah 0.0067 %, sedangkan hasil penyimpangan metode manual adalah 1.132 %. Berdasarkan data tersebut, terdapat penurunan hasil penyimpangan dengan kemampuan akurasi alat dua angka di belakang koma dilengkapi display dan hasil pencatatan otomatis terekam pada excel. Sehingga tercapainya keakuratan pengkuran Coil Track Circuit Reader sesuai dengan standar, memudahkan perekaman data pengukuran serta meningkatkan keselamatan pekerja.
Downloads
References
D. Maryani and Z. Abidin, “Jakarta-Bandung High-Speed Train Infrastructure Development Incollaborative Governance,” J. Ilm. Adm. Pemerintah. Drh., vol. 14, no. 1, pp. 162–179, 2021.
W. Riyanta, “Precautions For Jakarta-Bandung High-Speed Rail Infrastructure Project Cooperation: Construction At Night And In Storm,” JUTEKS J. Tek. Sipil, vol. 8, no. 1, p. 39, 2023, doi: 10.32511/juteks.v8i1.967.
B. P. P. Nasional, “A Decade Journey,” 2024.
KCIC, Peraturan Nomor 9 Direksi PT Kereta Cepat Indonesia China. 2023.
KCIC, Peraturan Nomor 13 Direksi PT Kereta Cepat Indonesia China. 2023.
T. Arifianto, D. B. Setyawan, and S. Sunaryo, “Penggunaan RFID (Radio Frequency Identification) CT-1809 Untuk Prototype Pendeteksi Sarana Berbasis Arduino Uno,” J. Telecommun. Electron. Control Eng., vol. 3, no. 2, pp. 71–80, 2021, doi: 10.20895/jtece.v3i2.328.
A. A. D. Prabawa, “Otomasi Alat Ukur dan Pencatat Otomatis Tinggi dan Berat Bayi Berbasis Arduino Uno,” 2018, [Online]. Available: http://sir.stikom.edu/id/eprint/2960/
A. Amdani, “Rancang Bangun Alat Ukur Tinggi Gelombang Air Laut Berbasis Mikrokontroller Arduino Uno,” Systematics, vol. 1, no. 2, p. 130, 2019, doi: 10.35706/sys.v1i2.2982.
S. Sharma, S. L. Thakur, S. K. Joshi, and S. S. Kulkarni, “Measurement of gingival thickness using digital vernier caliper and ultrasonographic method: a comparative study,” J. Investig. Clin. Dent., vol. 5, no. 2, pp. 138–143, 2014, doi: 10.1111/jicd.12026.
A. P. Ion et al., “Superior Measurement Accuracy of Digital Thickness Gauge Versus Digital Vernier Caliper in Determining Venous Tissue Thickness,” Cureus, vol. 16, no. 9, 2024, doi: 10.7759/cureus.68442.
Z. Lewandowski, E. Dychała, A. Pisula-Lewandowska, and D. P. Danel, “Comparison of Skinfold Thickness Measured by Caliper and Ultrasound Scanner in Normative Weight Women,” Int. J. Environ. Res. Public Health, vol. 19, no. 23, 2022, doi: 10.3390/ijerph192316230.
Downloads
Published
How to Cite
Issue
Section
License
The copyright to this article is transferred to Universitas Mercu Buana (UMB) if and when the article is accepted for publication. The undersigned hereby transfers any and all rights in and to the paper including without limitation all copyrights to UMB. The undersigned hereby represents and warrants that the paper is original and that he/she is the author of the paper, except for material that is clearly identified as to its original source, with permission notices from the copyright owners where required. The undersigned represents that he/she has the power and authority to make and execute this assignment.
We declare that:
1. This paper has not been published in the same form elsewhere.
2. It will not be submitted anywhere else for publication prior to acceptance/rejection by this Journal.
3. A copyright permission is obtained for materials published elsewhere and which require this permission for reproduction.
Furthermore, I/We hereby transfer the unlimited rights of publication of the above mentioned paper in whole to UMB. The copyright transfer covers the exclusive right to reproduce and distribute the article, including reprints, translations, photographic reproductions, microform, electronic form (offline, online) or any other reproductions of similar nature.
The corresponding author signs for and accepts responsibility for releasing this material on behalf of any and all co-authors. This agreement is to be signed by at least one of the authors who have obtained the assent of the co-author(s) where applicable. After submission of this agreement signed by the corresponding author, changes of authorship or in the order of the authors listed will not be accepted.
Retained Rights/Terms and Conditions
1. Authors retain all proprietary rights in any process, procedure, or article of manufacture described in the Work.
2. Authors may reproduce or authorize others to reproduce the Work or derivative works for the authors personal use or for company use, provided that the source and the UMB copyright notice are indicated, the copies are not used in any way that implies UMB endorsement of a product or service of any employer, and the copies themselves are not offered for sale.
3. Although authors are permitted to re-use all or portions of the Work in other works, this does not include granting third-party requests for reprinting, republishing, or other types of re-use.
