PERANCANGAN DAN SIMULASI STRUKTUR RANGKA OVERHAUL STAND UNTUK PENGGUNAAN ASSEMBLY DAN DIASSEMBLY HYDRAULIC CYLINDER MENGGUNAKAN SOFTWARE SOLIDWORK
DOI:
https://doi.org/10.22441/jtm.v10i1.10778Keywords:
Hydraulic cylinder, Overhaul Stand, Finite Element Analysis, tegangan, factor keamananAbstract
Penelitian ini bertujuan untuk menganalisis struktur dari Overhaul Stand yang digunakan sebagai alat bantu untuk menopang hydraulic cylinder dalam proses pemeriksaan dan perbaikan. Dalam hydraulic cylinder terdapat piston yang terhubung dengan rod yang dapat bergerak maju dan mundur, bergantung pada sisi mana yang diisi oleh fluida hidrolik bertekanan. Metode yang digunakan dalam perancangan ini meliputi pengumpulan data, membuat model pada perangkat lunak, kemudian menganalisis struktur menggunakan metode simulasi Finite Element Analysis (FEA). Hasil simulasi FEA mendapatkan nilai tegangan dan faktor keamanan pada Overhaul Stand yang mengalami pembebanan dari hydraulic cylinder. Berdasarkan hasil simulasi, pengujian dengan menggunakan material JIS 3101 SS 400, struktur Overhaul Stand berada dalam batas aman.
Downloads
References
Davinci, Ronaldo, and Dedi Yulhendra. "Pengendalian Waktu Efektif Bulldozer CAT D8R Rental Untuk Meminimalisasi Biaya Operasional Di PT Bukit Asam Tbk Unit Pelabuhan Tarahan Bandar Lampung." Bina Tambang 4.1 (2019): 81-91.
Xu, Zhaomei, and Yuwei Dong. "Modal analysis of transmission gear in gearbox based on SolidWorks." 2011 Second International Conference on Mechanic Automation and Control Engineering. IEEE, 2011.
Glodová, Iveta, Tomáš Lipták, and Jozef Bocko. "Usage of finite element method for motion and thermal analysis of a specific object in SolidWorks environment." Procedia Engineering 96 (2014): 131-135.
Chirită, Ionel, et al. "Design optimization of a flywheel using solidworks modeling and simulation capabilities." 2017 International Conference on ENERGY and ENVIRONMENT (CIEM). IEEE, 2017.
Li, Donghua. "Strength check simulation analysis of forming machine piston." 2014 International Conference on Advances in Engineering & Technology Research (ICAETR-2014). IEEE, 2014.
Sam, Rosidah, Kamarul Arrifin, and Norlida Buniyamin. "Simulation of pick and place robotics system using Solidworks Softmotion." 2012 International Conference on System Engineering and Technology (ICSET). IEEE, 2012.
Mu, Xiaoqi, et al. "Structural characteristic analysis of multifunctional elderly-assistant and walking-assistant robot based on SolidWorks/simulation." 2017 14th International Conference on Ubiquitous Robots and Ambient Intelligence (URAI). IEEE, 2017.
Suhaimi, Wan Hanif Hazwan Wan, et al. "Design and analysis of a gate valve fluid flow using SolidWorks simulation software." 2014 2nd International Conference on Electrical, Electronics and System Engineering (ICEESE). IEEE, 2014.
Halim, Levin, and David Nathanlius. "Simulasi Perancangan Turbin Propeller untuk Pembangkit Listrik Tenaga Air Berdasarkan Karakteristik Sungai Maliringan Dengan Metode Computational Dynamics Fluid (CFD)." Jurnal Teknik Mesin 8.1 (2019).
Y. Iwamoto, “Introduction of Products Introduction of Komatsu ’ s New Hydraulic Excavator PC200-7 in GALEO Series,” vol. 48, no. 149, 2002, pp. 35–44
M.D. Aqshal and Nurato, “Analisis Perbandingan Faktor Keamanan Rangka Scooter Menggunakan Perangkat Lunak Solidwork 2015, Jurnal Teknik Mesin vol 9.No.3 (2020).
Downloads
Published
How to Cite
Issue
Section
License
The copyright to this article is transferred to Universitas Mercu Buana (UMB) if and when the article is accepted for publication. The undersigned hereby transfers any and all rights in and to the paper including without limitation all copyrights to UMB. The undersigned hereby represents and warrants that the paper is original and that he/she is the author of the paper, except for material that is clearly identified as to its original source, with permission notices from the copyright owners where required. The undersigned represents that he/she has the power and authority to make and execute this assignment.
We declare that:
1. This paper has not been published in the same form elsewhere.
2. It will not be submitted anywhere else for publication prior to acceptance/rejection by this Journal.
3. A copyright permission is obtained for materials published elsewhere and which require this permission for reproduction.
Furthermore, I/We hereby transfer the unlimited rights of publication of the above mentioned paper in whole to UMB. The copyright transfer covers the exclusive right to reproduce and distribute the article, including reprints, translations, photographic reproductions, microform, electronic form (offline, online) or any other reproductions of similar nature.
The corresponding author signs for and accepts responsibility for releasing this material on behalf of any and all co-authors. This agreement is to be signed by at least one of the authors who have obtained the assent of the co-author(s) where applicable. After submission of this agreement signed by the corresponding author, changes of authorship or in the order of the authors listed will not be accepted.
Retained Rights/Terms and Conditions
1. Authors retain all proprietary rights in any process, procedure, or article of manufacture described in the Work.
2. Authors may reproduce or authorize others to reproduce the Work or derivative works for the authors personal use or for company use, provided that the source and the UMB copyright notice are indicated, the copies are not used in any way that implies UMB endorsement of a product or service of any employer, and the copies themselves are not offered for sale.
3. Although authors are permitted to re-use all or portions of the Work in other works, this does not include granting third-party requests for reprinting, republishing, or other types of re-use.
This work is also licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
