INVESTIGASI RASIO PANJANG INLET GUIDE VANE DAN DUCTING DENGAN ANALISA NUMERIK TERHADAP POLA ALIRAN DAN KECEPATAN KELUARAN OUTLET DUCTING

fajar anggara

Abstract


In this research, air flowing from condenser of cold room has been used to turning turbine through ducting. In term of installation the guide vane in the ducting, air flowing is directed to turbine blade. This investigation using ANSYS FLUENT 17 to determine the dimension ratio of length between guide vane and ducting. By comparing three variations A, B and C that the best ratio is B by producing 9.2-9.4 m/s at the outlet of ducting. This is due to the degree of the guide van B is smaller than A and the distance to increase velocity is longer than guide vane C.

Keywords


Numeric, CFD, ducting, ratio dimension, turbine

References


P. R. Ansyah, J. Waluyo, Suhanan, M. Najib, and F. Anggara, “Thermal behavior of melting paraffin wax process in cylindrical capsule by experimental study,” vol. 020008, p. 020008, 2018.

R. A. Anugrah, A. Widyaparaga, I. M. Miasa, J. Waluyo, Sugiyanto, and S. Kamal, “Experimental study on performance of standing-wave thermoacoustic engine at different tilted angles and resonator length,” AIP Conf. Proc., vol. 2001, no. August, 2018.

A. M. Rasham and J. M. Mahdi, “Performance of wind turbines at three sites in Iraq,” Int. J. Renew. Energy Res., vol. 8, no. 3, pp. 1327–1338, 2018.

A. Annuk et al., “Increasing self electricity consumption by using double water heating tanks for residential net zeroenergy buildings,” 2017 6th Int. Conf. Renew. Energy Res. Appl. ICRERA 2017, vol. 2017-Janua, pp. 106–110, 2017.

I. Keskin and G. Soykan, “Reduction of peak power consumption by using photovoltaic panels in Turkey,” 2017 6th Int. Conf. Renew. Energy Res. Appl. ICRERA 2017, vol. 2017-Janua, pp. 886–890, 2017.

X. Wang et al., “Grey relational analysis and optimization of guide vane for reactor coolant pump in the coasting transient process,” Ann. Nucl. Energy, vol. 133, pp. 431–440, 2019.

S. Chitrakar, H. P. Neopane, and O. G. Dahlhaug, “Development of a test rig for investigating the flow field around guide vanes of Francis turbines,” Flow Meas. Instrum., vol. 70, p. 101648, 2019.

C. T. Shaw, “Using computational fluid dynamics,” Book, vol. 22, no. 3, p. 323, 1992.

F. Anggara et al., “Simulation and validation of PCM melting in concentric double pipe heat exchanger,” AIP Conf. Proc., vol. 2001, 2018.

B. Y. Prawira and C. Soekardi, “Analisis Aliran Uap Pada Nozzle Tip Sampling Probe Pltp Menggunakan Computational Fluid Dynamics,” Sinergi, vol. 21, no. 3, p. 213, 2017.

T. A. G. Langrish and D. F. Fletcher, “Spray drying of food ingredients and applications of CFD in spray drying,” Chem. Eng. Process., vol. 40, no. 4, pp. 345–354, 2001.




DOI: http://dx.doi.org/10.22441/jtm.v9i2.7905

Refbacks

  • There are currently no refbacks.


Copyright (c) 2020 Jurnal Teknik Mesin

Jurnal Teknik Mesin (JTM)
Program Studi Teknik Mesin, Fakultas Teknik, Universitas Mercu Buana
Jl. Meruya Selatan No. 01, Kembangan, Jakarta Barat 11650, Indonesia
Email: [email protected]
Telp.: 021-5840815/ 021-5840816 (Hunting)
Fax.: 021-5871335

JTM is indexed by the following abstracting and indexing services:

Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

View My Stats