Application of Failure Mode and Effect Analysis (FMEA) for Defect Reduction: A Case Study on Scratch Defects in Oil Separator Parts in Machining Line

Fredy Sumasto, Jean Christiani, Isma Wulansari, Muhamad Fahrul Rozi, Arif Dzulfikar, Ahlan Ismono

Abstract


This study addresses the problem of significant defect rates on Oil Separator Parts in machining line, especially focusing on scratch defects. The defect rate reached 0.495%, exceeding the company's target of 0.1%. In the approach using FMEA, potential failure modes were identified and rated based on Risk Priority Number to plan corrective actions. Effort and Impact Analysis was used to analyze the most effective action recommendations. Implementation of the 5S methodology was selected as the improvement solution, which focused on workplace organization, maintenance, and cleanliness. The results were positive, with the number of defects decreasing dramatically from 540 to 67 units in July 2023, and the defect rate dropping from 0.495% to 0.145%. Although the company's quality targets have not been fully achieved, the FMEA approach and 5S implementation have been shown to significantly improve production quality and reduce defects. This study proves that this approach has the potential to address complex quality issues, although further challenges may be required to achieve the final goals set.

Keywords


5S; Automotive parts; Effort and impact analysis; FMEA; Quality

Full Text:

PDF

References


Dewi, S. R., Setiawan, B., & Susatyo Nugroho, W. P. (2013). 5S program to reduce change-over time on forming department (case study on CV Piranti Works temanggung). IOP Conference Series: Materials Science and Engineering, 46(1). https://doi.org/10.1088/1757-899X/46/1/012040

Febriana, T. H., Dewita, H., Hermawan, C., & Herlambang, H. (2020). Perbaikan Ketahanan Lifetime Bladder untuk Peningkatan Curing Efficiency pada Proses Industri Tire Manufacture. IJIEM - Indonesian Journal of Industrial Engineering and Management, 1(1), 33. https://doi.org/10.22441/ijiem.v1i1.9258

Iska Aprilia Wardhani, M., Nikmatullah Realita, T., Studi Manajemen, P., & Indocakti Malang, S. (2022). SOSMANIORA (Jurnal Ilmu Sosial dan Humaniora) 5S As a Form of Lean Manufacturing Implementation in the Perspective of Human Resources: A Case Study in Food SMEs. 1(4), 599–605. https://doi.org/10.55123/sosmaniora.v1i4.1275

Kholil, M. (2023). Lean Manufacturing Implementation to Reduce Reject on Part Step Floor with DMAIC and FMEA approach. 3(6), 11–19. https://doi.org/10.54756/IJSAR.2023.V3.6.2

Millenia, T. P., Muhammad, F., & Handoko, B. (2023). Implementation of the 5S Work Attitude Using the Lean Six Sigma Method to the Performance Productivity of Medical Records Unit Officers of Arifin Achmad Hospital, Riau Province. Journal of Health Sciences, 16(01), 43–50. https://doi.org/10.33086/jhs.v16i01.3701

Neves, P., Silva, F. J. G., Ferreira, L. P., Pereira, T., Gouveia, A., & Pimentel, C. (2018). Implementing Lean Tools in the Manufacturing Process of Trimmings Products. Procedia Manufacturing, 17, 696–704. https://doi.org/10.1016/j.promfg.2018.10.119

Novianti, F., & Rochmoeljati, R. (2023). Quality Control of Edamame Products Using Statistical Quality Control ( SQC ) and Failure Mode Effect Analysis ( FMEA ) Methods in PT. XYZ. Indonesian Journal of Industrial Engineering & Management, 4(2), 221–230. https://doi.org/10.22441/ijiem.v4i2.20550

Pérez-Pucheta, C. E., Olivares-benitez, E., & Minor-popocatl, H. (2019). Implementation of Lean Manufacturing to Reduce the Delivery Time of a Replacement Part to Dealers : A Case Study. Applied Sciences, 9(3932), 1–23.

Shahriar, M. M., Parvez, M. S., Islam, M. A., & Talapatra, S. (2022). Implementation of 5S in a plastic bag manufacturing industry: A case study. Cleaner Engineering and Technology, 8(April), 100488. https://doi.org/10.1016/j.clet.2022.100488

Sharma, S. S., Shukla, D. D., & Sharma, B. P. (2019). Analysis of lean manufacturing implementation in SMEs: A “5S” technique. In Lecture Notes in Mechanical Engineering. Springer Singapore. https://doi.org/10.1007/978-981-13-6412-9_46

Solihudin, M., Nurhidayat, W., Suwandi, S., Bakti, C. S., Rachmat, R., Hadi, A. H., & Nugroho, S. (2023). Implementation of Tree Diagram Method, Failure Mode Effect Analysis (FMEA) and 5W 1H to Reduce Corky Defective Products in PT. XYZ. IJIEM - Indonesian Journal of Industrial Engineering and Management, 4(1), 18. https://doi.org/10.22441/ijiem.v4i1.17237

Sumasto, F., Akbar, M. R., Fajri, S., & Husna, H. (2023). Peningkatan Value Added dalam Industri Tahu melalui Penerapan Lean Manufacturing dan Analisis Waste. Jurnal Serambi Engineering, VIII(4), 7338–7347. https://doi.org/10.32672/jse.v8i4.6876

Sumasto, F., Arliananda, D. A., Imansuri, F., Aisyah, S., & Pratama, I. R. (2023). Fault Tree Analysis: A Path to Improving Quality in Part Stay Protector A Comp. Journal Européen Des Systèmes Automatisés, 56(05), 757–764. https://doi.org/10.18280/jesa.560506

Sumasto, F., Arliananda, D. A., Imansuri, F., Aisyah, S., & Purwojatmiko, B. H. (2023). Enhancing Automotive Part Quality in SMEs through DMAIC Implementation : A Case Study in Indonesian Automotive Manufacturing. Quality Innovation Prosperity, 27(3), 57–74. https://doi.org/10.12776/QIP.V27I3.1889

Sumasto, F., Maharani, C. P., Purwojatmiko, B. H., Imansuri, F., & Aisyah, S. (2023). PDCA Method Implementation to Reduce the Potential Product Defects in the Automotive Components Industry. Indonesian Journal of Industrial Engineering & Management, 4(2), 87–98. https://doi.org/10.22441/ijiem.v4i2.19527

Sumasto, F., Nugroho, Y. A., Purwojatmiko, B. H., Wirandi, M., Imansuri, F., & Aisyah, S. (2023). Implementation of Measurement System Analysis to Reduce Measurement Process Failures on Part Reinf BK6. Indonesian Journal of Industrial Engineering & Management, 4(2), 212–220. https://doi.org/10.22441/ijiem.v4i2.20212

Sumasto, F., Riyanto, A., Pratama, I. R., Imansuri, F., & Putri, A. (2023). Meningkatkan Produktivitas di Sektor Otomotif ( Studi Kasus : Yanto ’ s Truck Seat Service ). Jurnal Serambi Engineering, VIII(4), 7356–7369. https://doi.org/10.32672/jse.v8i4.6898

Sumasto, F., Safril, S., Imansuri, F., & Wirandi, M. (2022). Penerapan Manajemen Kualitas Terpadu Pada Industri Makanan Skala Mikro, Kecil Dan Menengah (Studi Kasus Umkm Nasi Goreng). Jurnal PASTI (Penelitian Dan Aplikasi Sistem Dan Teknik Industri), 16(3), 274. https://doi.org/10.22441/pasti.2022.v16i3.003

Sumasto, F., Satria, P., & Rusmiati, E. (2022). Implementasi Pendekatan DMAIC untuk Quality Improvement pada Industri Manufaktur Kereta Api. Jurnal INTECH Teknik Industri Universitas Serang Raya, 8(2), 161–170. https://doi.org/doi.org/10.30656/intech.v8i2.4734

Suresh Kumar, B., & Syath Abuthakeer, S. (2012). Implementation of lean tools and techniques in an automotive industry. Journal of Applied Sciences, 12(10), 1032–1037. https://doi.org/10.3923/jas.2012.1032.1037

Tarigan, U. P. P., & Budiman, I. (2021). Implementasi Metode Lean Service dan 5S untuk Meningkatkan Efisiensi Waktu Pelayanan di Dinas Pencegah dan Pemadam Kebakaran Kota Medan. Jurnal Sistem Teknik Industri, 23(1), 59–68. https://doi.org/10.32734/jsti.v23i1.4891

Wahjudi, D., & Cahyadi, A. (2022). Implementasi FMEA untuk Peningkatan Produktifitas di PT. X. Jurnal Teknik Mesin, 19(2), 45–50. https://doi.org/10.9744/jtm.19.2.45-50

Wahjudi, D., & Projesa, Y. D. P. (2021). An FMEA-Based Approach to Waste Reduction A Case on a Make-to-Order Company. Proceedings of the International Conference on Business and Engineering Management (ICONBEM 2021), 177, 7–11. https://doi.org/10.2991/aebmr.k.210522.002

Zuniawan, A. (2020). A Systematic Literature Review of Failure Mode and Effect Analysis (FMEA) Implementation in Industries. IJIEM - Indonesian Journal of Industrial Engineering and Management, 1(2), 59. https://doi.org/10.22441/ijiem.v1i2.9862




DOI: http://dx.doi.org/10.22441/ijiem.v4i3.22768

Refbacks

  • There are currently no refbacks.


Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

IJIEM - Indonesian Journal of Industrial Engineering & Management
Program Pascasarjana Magister Teknik Industri Universitas Mercu Buana
Kampus Menteng - Gedung Tedja Buana, Floor 4th  
Jl. Menteng Raya No. 29  Jakarta Pusat- Indonesia
Tlp.: +62 21 31935454 Fax: +62  21 31934474
http://publikasi.mercubuana.ac.id/index.php/ijiem

Email:  [email protected]

 

Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

 

Web Analytics Made Easy - Statcounter View My Stats

The journal is indexed by: