PENGARUH WAKTU PENGADUKAN TERHADAP UKURAN KRISTALIT DAN HAMBATAN JENIS Al-Ti MENGGUNAKAN TEKNIK PEMADUAN MEKANIK
Abstract
Full Text:
PDFReferences
. Zhan, Z., He, Y., Wang, D. and Gao, W. 2006. Low-temperature Processing of Fe–Al Intermetallic Coatings Assisted by Ball Milling. Intermetallics 14: 75–81.
. Fan, G.J., Choo, H., Liaw, P.K. and Lavernia, E.J. 2006. Plastic Deformation and Fracture of Ultrafine-grained Al–Mg Alloys with a Bimodal Grain Size Distribution. Acta Materialia 54: 1759–1766.
. Dahle, A.K., Nogita, K., McDonald, S.D., Dinnis, C. and Lu, L. 2005. Eutectic Modification and Microstructure Development in Al–Si Alloys. Materials Science and Engineering A 413–414: 243–248.
. Li, X., Hui, D., Xuefong, R. and Yaoyao, R. 2007. Microstructures of mechanically activated Ti-46at. % A1 powders and spark plasma sintered ultrafine TiAl alloy. Rare Metals 26(6): 572 – 577.
. Xiaoying Zhu et al. 2006. Oxidation of Mechanically Allyed Al-rich Al-Ti Powder. Oxidation of metals 65: 357 – 376.
. Lauer, St., Guan, Z., Wolf, H. and Wichert, Th. 2002. Investigation of mechanical alloying of Ti–Al compounds using perturbed -angular correlation spectroscopy, x-ray diffraction, and differential scanning calorimetry. J. Mater. Res. 17(8): 2130 – 2139.
. Calderon, H.A., Garibay-Febles, V., Cabrera, A., Cabanas-Moreno, J.G. and Umemoto, M. 2001. Mechanical Properties of Nanocrystalline TiAl-X and TiAl3-X Prepared by Mechanical Alloying and Sintering. Materials Science Forum 360-362: 229 – 234.Cao, G, Geng, L., Zheng. Z, & Naka, M. 2007. The Oxidation of Nanocrystalline Ni3Al Fabricated by Mechanical Alloying and Spark Plasma Sintering. Intermetallics.15: 1672 – 1677.
. Belyakov, A., Sakai, Y., Hara, T., Kimura, Y. and Tsuzaki, K. 2003. Annealing Behavior of Submicrocrystalline Oxide-Bearing Iron Produced by Mechanical Alloying. Metallurgical and Materials Transactions, 34A: 131 – 138.
. Bonastre, J., Escoda, L., González, A., Saurina, J. and Suñol, J. 2007. Influence of Ni content on Fe–Nb–B alloy formation. Journal of Thermal Analysis and Calorimetry, 88(1): 83 – 86.
. Barona Mercado, W., Fajardo, M., Perez Alcazar, G. A. and Sanchez Sthepa, H. 2006. Synthesis and characterization of Fe3AIC0.5 by mechanical alloying. Hyperfine interactions 169: 943 – 949.
. Chicinas, I., Pop, V. and Isnard, O. 2004. Journal of Materials Science 39: 5305 – 5309.
. Angelo L. D., Gonz’ales G. & Ochoa, J. 2007. Phase Transformations Study on Ni75Al25 and Ni50Al50 during Mechanical Alloying and Sintering. Journal of alloys and compounds: 345 – 353.
. Enayati M. H., Sadeghian Z., Salehi, M and Saidi A. 2004. The Effect of milling Parameters on the Synthesis of Ni3Al Intermetallic Compound by Mechanical Alloying. Materials Science and Engineering A. 375 – 377: 809 – 811.
. Cuevas, F.G., Cintas, J., Montes, J.M. and Gallardo, J.M. 2006. Al-Ti Powder Produced Through Mechanical Alloying for Different Time. J Master Sci 41: 8339 – 8346.
. Joshi, P. B., Marathe, G. R., Arun Pratap and Vinod Kurup. 2005. Hyperfine interactions 160: 173 – 180.
. Lu, L. And Lai M. O. 1998. Mechanical Alloying. Kluwer Academic Publisher, London 29.
. Khaloobagheri, M. and Barfjan, S.A. 2015. The Effect of Milling Time on Properties and Microstructure of Cu-Yttria Stabilized Zirconia Composites Fabricated by Powder Metallurgy. Journal of Materials Sciences and Applications 1(2): 78 – 84.
DOI: http://dx.doi.org/10.22441/jtm.v6i4.2023
Refbacks
- There are currently no refbacks.
Copyright (c) 2018 Jurnal Teknik Mesin
Jurnal Teknik Mesin (JTM)
Program Studi Teknik Mesin, Fakultas Teknik, Universitas Mercu Buana
Jl. Meruya Selatan No. 01, Kembangan, Jakarta Barat 11650, Indonesia
Email: [email protected]
Telp.: 021-5840815/ 021-5840816 (Hunting)
Fax.: 021-5871335
JTM is indexed by the following abstracting and indexing services:
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.