Effect of Intake Manifold Porting and Polishing and Throttle Body Venturi Diameter Modification on Motorcycle Performance

GUN GUN ANBIA

Abstract


This study aims to investigate the effect of intake manifold and throttle body modifications on the performance of a Yamaha Mio M3 125cc motorcycle engine. A two-level factorial experimental design with two factors was employed: intake manifold diameter (27 mm and 30 mm) and throttle body diameter (26 mm and 28 mm). Data were collected using a dyno test and analyzed using statistical methods. The results revealed that intake manifold and throttle body modifications significantly influenced the performance of the Yamaha Mio M3 125cc motorcycle engine. The combination of a 27 mm intake manifold and a 28 mm throttle body produced the highest torque of 23.1 Nm at 2,058 RPM, while the combination of a 27 mm intake manifold and a 26 mm throttle body generated the highest power of 11.2 HP at 7,155 RPM. These modifications resulted in a 10.53% increase in torque and a 16.67% increase in power compared to the standard configuration. Modifying the intake manifold and throttle body can enhance the performance of the Yamaha Mio M3 125cc motorcycle engine.

 

Keywords: Intake manifold modification, Throttle body modification, Engine performance, Yamaha Mio M3 125cc


References


Mafruddin, E. Nugroho, Asroni, and N. Rajabiah, “Solusi Dan Target Luaran Permasalahan utama yang dihadapi oleh siswa yaitu belum mengetahui dasar-dasar,” vol. 4, no. 1, pp. 29–34, 2020.

D. D. Handoko, D. N. Zulfika, and A. I. Dyah, “Pengaruh Perbandingan Injektor Standart Dan Injektor Racing Brt Terhadap Performa Mesin Honda Adv 150 Cc,” Semin. Nas. Fak. Tek., vol. 1, no. 1, pp. 61–67, 2022, doi: 10.36815/semastek.v1i1.11.

M. M. Al Fikri, “Analisa Sistem Kerja Electrical Fuel Injection (EFI) pada Motor Honda CBR 150,” Majamecha, vol. 1, no. 1, pp. 36–47, 2019, doi: 10.36815/majamecha.v1i1.366.

A. A. Lerryck, S. Buyung, and Y. Pakan, “Analisis Pengaruh Variasi Suhu Udara Masuk Dan Putaran Motor Terhadap Durasi Penyemprotan Bahan Bakar Pada Sepeda Motor Matic 4 Tak,” J. Voering, vol. 7, no. 1, pp. 16–23, 2022.

L. Q. Harahap and Junaidi, “Analisa Performa Honda Supra X 125 Menggunakan Karburator Standart Dan Karburator Racing Berbahan Bakar Pertalite,” Cetak) Bul. Utama Tek., vol. 17, no. 2, pp. 1410–4520, 2022.

S. Mahendra and D. Rohmantoro, “Pengaruh Performa Mesin Sepeda Motor Matik 4 TAK 110 CC Terhadap Penggunaan Piggiback Fuel Adjuster Iquteche,” J. Automot. Technol. Vocat. Educ., vol. 02, no. 2, pp. 1–9, 2021.

M. Ghozali, “Modifikasi Intake manifold Terhadap Performa Mesin Motor Yamaha Mio Soul Tahun 2008,” Saintesa, vol. 1, pp. 7–13, 2021.

E. Bambang, W. T. Putra, and M. Malyadi, “Jurnal Ilmiah Mahasiswa Universitas Muhammadiyah Ponorogo (Komputek) Analisa Efek Perubahan Venturi Karburator Terhadap Performance Mesin Pada Sepeda Motor Yamaha Vega,” vol. 0985, pp. 1–13, 2019.

F. Majedi and I. Puspitasari, “Optimasi Daya dan Torsi pada Motor 4 Tak dengan Modifikasi Crankshaft dan Porting pada Cylinder Head,” JTT (Jurnal Teknol. Terpadu), vol. 5, no. 1, p. 82, 2017, doi: 10.32487/jtt.v5i1.216.

I. W. Prasetyo, “J-MEEG,” vol. 1, no. 2, pp. 200–205, 2023.

A. A. Hanif, S. Widodo, and R. P. Dewi, “STUDI EKSPERIMEN PERFORMA DAN KONSUMSI BAHAN BAKAR TERHADAP PERLAKUAN PORTING POLISH MODEL BOLA GOLF PADA SEPEDA MOTOR MATIC 4 TAK KONVENSIONAL,” no. 3, pp. 4–7, 2023.

& A. F. Rizki Fajarudin, Agus Wibowo, “Analisa Modifikasi Intake manifold Terhadap Kinerja Mesin Sepeda Motor 4 Tak 110cc,” Univ. Pancasakti, Tegal, vol. 12 no 1, no. April 2016, p. 36, 2016.

K. N. Rokhman, S. Sumarli, and P. Paryono, “Pengaruh Modifikasi Ukuran Lubang Intake manifold Terhadap Konsumsi Bahan Bakar Dan Performansi Kendaraan Sepeda Motor Honda 4 Tak 125Cc,” J. Tek. Otomotif Kaji. Keilmuan dan Pengajaran, vol. 5, no. 2, p. 7, 2021, doi: 10.17977/um074v5i22021p7-12.

R. Lapisa, R. Rahman, I. Yulia Basri, and W. Afnison, “Pengaruh Diameter Variasi Throttle body Terhadap Daya, Torsi Dan Emisi Gas Buang Pada Sepeda Motor Beat Pgm-Fi 110 Cc Tahun 2014,” Ensiklopedia Educ. Rev., vol. 4, no. 3, pp. 245–250, 2022, doi: 10.33559/eer.v4i3.1544.

S. Putri and E. Edwarman, “Hubungan Produk,Merek,Dan Promosi Terhadap Keputusan Pembelian Sepeda Motor Yamaha Mio M3 Di PT Thamrin Brother Argamakmur,” J. Adm. Bisnis Nusant., vol. 2, no. 2, pp. 65–78, 2023, doi: 10.56135/jabnus.v2i2.119.




DOI: http://dx.doi.org/10.22441/jtm.v13i2.27416

Refbacks

  • There are currently no refbacks.


Copyright (c) 2024 Jurnal Teknik Mesin

Jurnal Teknik Mesin (JTM)
Program Studi Teknik Mesin, Fakultas Teknik, Universitas Mercu Buana
Jl. Meruya Selatan No. 01, Kembangan, Jakarta Barat 11650, Indonesia
Email: [email protected]
Telp.: 021-5840815/ 021-5840816 (Hunting)
Fax.: 021-5871335

JTM is indexed by the following abstracting and indexing services:

 

 

Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

View My Stats