Parametric Optimization under Cryogenic Machining of Medium Carbon Low Alloy Steel EN-19 Using the Integrated Taguchi-Present Worth Method

Sunday Ayoola Oke

Abstract


Medium carbon low alloy steel En-19 is a commercially thriving work material with 0.30 to 0.50% as carbon content and 0.60 to 1.65% as manganese content. The wide range of uses of medium carbon steel is for shafts, crankshafts, forgings, axles, couplings and gears. Given the broad industrial usage, the optimization of this work material is currently indispensable since it is a pointer to the economic management of drilling resources and a justifiable metric for performance assessment and evaluation. However, the present optimization models during machining have inaccurate predictions as they exclude the economic aspect of the material. In this article, a new combined Taguchi (T) method-present worth (PW) method is presented to account for the present worth and the inflation rate of steel material within the optimization context using literature data. The amalgamation of the two-component methods of Taguchi and present work is done at the signal-to-noise calculation. Then the response table, optimal parametric setting, the performance flow diagram and the present worth values are finally established. For the results, the optimal parametric setting was ascertained as SP3FR2DOC1, obtained at 37.48 (level 3), 35.92 (level 2) and 36.31 (level 1) for speed, feed rate and depth of cut, respectively, interpreted as 900rpm (speed), 0.1mm/min (feed rate) and 0.5mm (depth of cut). The T-PW method yields PWSP (62.85) as 1st, PWFR (-64.64) as 2nd and PWDOC (-65.13) as the 3rd position. It was found that the speed parameter is the best based on the optimization cum economic aspect assessment. The T-PW method predicts the optimization behaviour while analysing the economic aspect of the steel material and would help plan the purpose. The findings in this study would assist to clarify the approach to analyzing the economic characteristics of the machining process.

Keywords


Optimization, economic benefit, Taguchi method, present worth method, optimal setting

Full Text:

PDF

References


Anthuvan R.N., Kumar S.P., Prakash R.A., Arunkarthik B., Akhilesh A. 2021, Machinability study in milling of Ti-6Al-4V using cryogenic treated and coated tool, Materials Today: Proceedings, In Press, https://doi.org/10.1016/j.matpr.2021.03.451

Balaji V., Ravi S., Chandran P.N., Damodaran K.M., 2015, Review of the cryogenic machining in turning and milling process, International Journal of Research in Engineering and Technology, Vol. 4, No. 10, pp. 38-42.

Bansal A., Singla A.L, Diviedi V., Goyal D.K., Singla J., Gupta M.K., Krolczyk G.M., 2020, Influence of cryogenic treatment on the mechanical performance of friction stir Al-Zn-Cu alloy weldments, Journal of manufacturing processes, Vol. 56, pp. 43-53

Barylski A., Aniolek K., Derez G., Kupka M, Kaptaez S., 2021, the effect of deep cryogenic treatment and precipitation hardening on the structure, micromechanical properties and wear of the Mg-Y-Nd- Zr alloy, Wear, Vol. 468-469, Article 283587

Bharat N., Bose P.S.C. 2021, An overview on machinability of hard to cut materials using laser assisted machining, Materials Today: Proceedings, Vol. 43, No. 1, pp. 665-672. https://doi.org/10.1016/j.matpr.2020.12.587

Bicek M., Dimont F., Courbon C., Pusavea F., Rech J., Kpac J., 2012, Cryogenic machining as an alternative turning process of normalized and hardened AISI 52100 bearing steel, Journal of Material Processing Technology, Vol. 212, No. 12, pp. 2609-2618

Choudhary R., Garg H., Prasad M., Kumar D., 2017, Effect of cryogenic treatment of tool electrode on the machining performance and surface finish during electrical discharge machining of Hastelloy C-4, Materials Today: Proceedings, Vol.4, No. 2, pp. 1158-1166. https://doi.org/10.1016/j.matpr.2017.01.132

Damir, A., Sadek A., Attia H., 2018, Characterization of machinability and environmental impact of cryogenic turning of Ti-6AL-4V, Procedia CIRP, Vol. 69, pp.893-898.

Das R.K., Sahoo A.K., Kumar R., Panda A. 2020, Performances of time-controlled pulse minimum quantity lubrication in machining of hard to cut material: A brief review, Materials Today: Proceedings, Vol. 23, No. 3, pp. 545-548. https://doi.org/10.1016/j.matpr.2019.05.404

Dhar N.R., Kamruzzaman M., Khan M.M.A, Chattopadhyay A.B., 2006, Effects of cryogenic cooling by liquid nitrogen jets on tool wear, surface finish and dimensional deviation in turning different steels, International Journal of Machining and Machinability of Materials, Vol. 1, No. 1, pp. 115-131.

Dhananchezian M., Rishabapriyan M, Rajashekar G., Narayanan S.S., 2018, Study the effect of cryogenic cooling on machinability characteristics during turning duplex stainless steel 2205, Materials Today: Proceedings, Vol 5, No. 5, pp.1206-12070.

Dhokey N.B., Maske S.S., Ghosh P., 2021, Effects of tempering and cryogenic treatment on wear and mechanical properties of hot work tool steel (HB), Materials Today. Proceedings, Vol. 43, No. 5, pp. 3006-3013

Dutta D.K. 1992, Planning and the regulatory role of the Indian state, Journal of Contemporary Asia, Vol. 22, No. 1, pp. 82-93. https://doi.org/10.1080/00472339280000071

Fantoneli D.G., Parcianellon C.T., Rosendo T.S., Reguly A., Tier M.D., 2020. Effect of heat and cryogenic treatment on wear and toughness of HSS AISI M2, Journal of Materials Research and Technology, Vol. 9 No. 6, 12354-12363)

Feucht F., Ketelaer J., Wolff A., Mori M., Fujishima M. 2014, Latest machining technologies of hard-to-cut materials by ultrasonic machine tool, Procedia CIRP, Vol. 14, pp. 148-152. https://doi.org/10.1016/j.procir.2014.03.040

Gross D., Bigelmaier M, Meier T., Amons S, Ostrowicki N., Hanenkamp N., 2019, Investigation of the influence of lubricating oils on the turning of metallic materials with cryogenic minimum quantity lubrication, Procedia CIRP, Vol. 80, pp.95-100.

Halim N.H.A, Chettaron C.H, Ghani J.A., Azhar M.F., 2018, Machining-induced microstructure of Inconel 718 in cryogenic environment, Progress in Industrial Ecology: An International Journal, Vol 12, No. 3, pp. 234-246

Jagadesh T., Samuel G.L., 2019, The influence of deep cryogenic treatment and in-situ cryogenic micro turning of Ti-6AL-4V on cutting forces, surface integrity and chip morphology, International Journal of Precision Technology., Vol. 8, No. 2/3/4, pp. 312-334

Jovicevic-Klug P., Jenko M., Jovicevic-Klug M., Setin B., 2021, Effect of deep cryogenic treatment on surface chemistry and microstructure of selected high-speed steels, Applied Surface Science, Vol. 548, Article 149257

Joviecevic–Klug P. and Podgornik B., 2020; comparative study of conventional and deep cryogenic treatment of AISI M3: 2 (EN 1. 2295) high-speed steel, Journal of Materials Research and Technology, Vol. 9, No. 6, pp 13118-13127.

Khare S.K., Phull G.S., Verma R.K., Agarwal S., 2021, A comparison between optimization techniques of cutting parameters under cryogenic machining process, Materials Today: Proceedings.

Khalil R. and Emadi H., 2020, An experimental investigation of cryogenic treatments reflects on porosity, permeability and mechanical properties of Marcellus downhole core samples, Journal of Natural Gas Science and Engineering, Vol. 81, Article 103422

Khann N., Agrawal C., Shadgaar J., Larsen, Phadmis V.A., 2019, Eco-friendly machining using retrofitted cryogenic machining system, Materials Today: Proceedings, Vol. 18, No 7, pp.2806-2813.

Krishnamoothy A., 2011, Some studies on modelling and optimization in drilling carbon fibre reinforced plastic composites, Ph.D. Thesis, Faculty of Mechanical Engineering, Anna University, Chennai, India

Mia M., 2017, Multi-response optimization of end milling parameters under through tool cryogenic cooling condition, measurement, Vol. 111, pp.134-145.

Muthuraman P., Karunakaran K., 2021, Optimisation of face milling process parameters by GRA with deep cryogenic treated milling cutter, Materials Today: Proceedings, Vol. 37, No. 2, pp. 1631-1617.

Nagimova A., Perveen A. 2019, A review on Laser Machining of hard to cut materials, Materials Today: Proceedings, Vol. 18, No. 7, pp. 2440-2447. https://doi.org/10.1016/j.matpr.2019.07.092

Nie G-C., Zhang X-M., 2018, An experimental study of the white layer formation during cryogenic assisted hard machining of AISI52100 steel, Procedia CIRP, Vol. 77, pp.223-226 Ozbek N.A., 2020, Effects of cryogenic treatment types on the performance of coasted tungsten tools in the turning of AISI H11 steel, Journal of Materials Research and Technology, Vol 9, No 4, pp. 9442-9456.

Oji B.C. and Oke S.A. 2020, Optimisation of bottling process using "hard' total quality management elements, The TQM Journal, Vol. 33, No. 2, pp. 473-502

Oke S.A. and Fagbolagun I.O., 2021, Optimisation of packaging process parameters using combined Taguchi method-present worth method/inflationary factor validated, International Journal of Industrial Engineering and Engineering Management, Accepted for publication.

Patil V.A., Jadhav B.R., 2019, Experimental investigation of cryogenic machining of EN-19 steel, Journal of Emerging Technologies and Innovation Research, Vol. 6, No 4, pp. 634-638

Pereira O., Rodriguez A., Ayesta I., Garcia J.B., Fernandez-Abia A.I., Lepez De Lacalle L.N., 2016, A cryo lubri-coolant approach for finish milling of aeronautical hard-to-cut materials, International Journal of Mechatronics and Manufacturing Systems, Vol. 9, No. 4, pp. 370-384.

Prakash D., Tariq M., Davis R., Singh A., Debnath K., 2021, Influence of cryogenic treatment on the performance of micro-EDM tool electrode in machining of magnesium alloy AZ31B, Materials Today: Proceedings, Vol. 39, No. 4, pp. 1198-1201. https://doi.org/10.1016/j.matpr.2020.03.589

Rahul, Datta S., Biswal B.B. 2019, Experimental studies on electro-discharge machining of Inconel 825 super alloy using cryogenically treated tool/workpiece, Measurement, Vol. 145, pp. 611-630. https://doi.org/10.1016/j.measurement.2019.06.006

Ramesh S., Bhuvaneshwari B., Palani G.S., Lad D.M., Mondal K., Gupta R.K., 2019, Enhancing the corrosion resistance performance of structural steel via a novel deep cryogenic treatment process, Vacuum, Vol. 159, pp 468-475

Ranjith R., Somu C., Tharanitharan G., Venkatajalapathi T., Naveenkumar M., 2019, Integrated Taguchi cum grey relational experimental analysis (GREAT) for optimization and machining characterization of cryogenic cooled AA6063 aluminium alloys, Material Today: Proceedings, Vol. 18, No. 7, pp. 3597-3605.

Rao P.S., Kumar S., Khan M.Y., 2020, Comparison of predicted capabilities of MRR parameter using RSM and ANN for dry turning of Inconel 825 alloy using cryogenically treated tungsten carbide tool, Materials Today: Proceedings, In press.

Rout I.S., Pandian P.P., Raj A. 2021, Experimental study of response parameters during machining of Inconel 718 with cryogenically treated ceramic round tool using cutting fluid, Materials Today: Proceedings, In Press, https://doi.org/10.1016/j.matpr.2021.04.573

Okafor A.C., Jasra P.M., 2019, effects of milling methods and cooling strategies on tool wear, chip morphology and surface roughness in high speed end milling of Inconel-718, International Journal of Machining and Machinability of Materials, Vol. 21, No 112, pp. 3-42.

Okponyia K.O. and Oke S.A., 2020, Exploring aluminium alloy metal matrix composites in EDM using coupled factor-level-present worth analysis and fuzzy analytic hierarchy process, International Journal of Industrial Engineering and Engineering Management, Vol. 2, No. 1, pp. 25-44.

Singh A and Grover N.K, 2015, Wear properties of cryogenic treated electrodes on machining of EN-31, Materials Today: Proceedings, Vol. 2, No. 4-5, pp. 1406-1413.

Sivaiah P., Chakradhard D., 2017, Multi-objective optimization of cryogenic turning process using Taguchi-based grey relational analysis, International Journal of Machining and Machinability of Materials, Vol. 19, No. 4, pp. 297-312.

Uysal A., Caudrill J.R, Javahir I.S., 2020, Minimizing carbon emissions and machining costs with improved human health in sustainable machining of austenitic stainless steel through multi-objective optimization, International Journal of Sustainable Manufacturing, Vol. 4, pp. 281-299.

Villa M., Somers M.A.J., 2020, cryogenic treatment of an AISI D2 steel: The role of isothermal martensite formation and martensite conditioning, Cryogenics, Vol. 110, Article 103131

Xue P., Huang, Y., Pauly S., Guo F., Ren Y., Jiang S., Guo F., Fan H., Ning H., 2021, structural evolution of a CuZr-based bulk metallic glass composite during cryogenic treatment observed by in-situ high-energy X-ray diffraction, Journal of Alloys and compounds, Vol. 871, Article 159570




DOI: http://dx.doi.org/10.22441/ijiem.v2i3.12196

Refbacks

  • There are currently no refbacks.


Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

IJIEM - Indonesian Journal of Industrial Engineering & Management
Program Pascasarjana Magister Teknik Industri Universitas Mercu Buana
Kampus Menteng - Gedung Tedja Buana, Floor 4th  
Jl. Menteng Raya No. 29  Jakarta Pusat- Indonesia
Tlp.: +62 21 31935454 Fax: +62  21 31934474
http://publikasi.mercubuana.ac.id/index.php/ijiem

Email:  [email protected]

 

Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

 

Web Analytics Made Easy - Statcounter View My Stats

The journal is indexed by: