Rancang Bangun Alat Transportasi Vertikal Menggunakan Atmega328
DOI:
https://doi.org/10.22441/jte.v10i1.002Abstrak
Abstrak—Semakin dibutuhkannya transportasi vertikal dengan biaya terjangkau tetapi tetap memenuhi standar keselamatan, diperlukan banyak inovasi yang sesuai dengan teknologi saat ini yaitu salah satunya menggunakan mikrokontroler sebagai kontrol basis utama mengoperasikan beberapa system kerja alat transportasi vertikal, salah satunya dirancang prototype lift dengan media yang relatife kecil dan mudah didapatkan yaitu Arduino. Alat transportasi vertikal dirancang menggunakan sebuah mikrokontroler berbasis arduino sebagai kontrol operasi utama lift, motor gearbox sebagai pengungkit pergerakan arah timing belt antara bandul dan sangkar lift, akrilik dipilih sebagai bahan prototype lantai, longdrat sebagai tiang pancang utama, kanal U berbahan akrilik juga dipilih sebagai rail untuk membatasi pergerakan sangkar dan bandul supaya tetap pada jalurnya, push button spst dipilih sebagai tombol pemanggil sangkar lift, pengarah tujuan lift dan emergency stop sangkar lift ketika terjadi masalah pada system, lampu led sebagai indicator arah tujuan sangkar lift dan posisi sangkar lift, batangan tembaga sebagai media level lantai. Penelitian ini mampu menghasilkan prototype dari sebuah lift dan sesuai dengan cara kerja lift dikehidupan nyata. Waktu tempuh satu lantai 12 detik dengan tinggi lantai 20 cm maka kecepatan dirumuskan (jarak tempuh antar lantai)/(waktu tempuh)=(20 cm)/(12 detik) = 1.6666667cm/det. Dalam pengoperasian alat simulator ini dalam waktu 8 jam mampu melayani 170 kali perjalanan bolak balikUnduhan
Referensi
A. Adriansyah dan O. Hidyatama, “Rancang Bangun Prototipe Elevator Menggunakan Mikrokontroler Arduino Atmega 328P”, Jurnal Teknologi Elektro, Universitas Mercu Buana, Vol. 4. No. 3, pp. 100-112, 2013.
DOI: http://dx.doi.org/10.22441/jte.v4i3.753
E. Ihsanto dan A. T. Wijayanto, “Rancang Bangun VIP Lift Dengan RFID Berbasis Mikrokontroler AT89S51”, Jurnal Teknologi Elektro, Universitas Mercu Buana. Vol. 4, No. 3. pp. 91-99, 2013.
DOI: http://dx.doi.org/10.22441/jte.v4i3.752
A. S. M. Lumenta, “Perancangan dan Simulasi Perangkat Lunak Sistem Kontrol Lift”, Jurnal Teknik Elektro dan Komputer, Universitas Sam Ratulangi, Vol. 3. No. 1. p. 87-97, 2014. DOI: https://doi.org/10.35793/jtek.3.1.2014.4290
J. R. Fernandez and P. Cortez, “A Survey of Elevator Group Control Systems for Vertical Transportation: A Look at Recent Literature”, IEEE Control Systems Magazine, Vol. 35, Issue: 4, pp. 38-55, August 2015.
DOI: https://doi.org/10.1109/MCS.2015.2427045
H. Wang, M. Zeng, Z. Xiong and F. Yang, “Finding main causes of elevator accidents via multi-dimensional association rule in edge computing environment”, China Communications. Vol. 14 , Issue: 11, pp. 39-47, November 2017. DOI: https://doi.org/10.1109/CC.2017.8233649
Unduhan
Diterbitkan
Cara Mengutip
Terbitan
Bagian
Lisensi
The copyright to this article is transferred to Universitas Mercu Buana (UMB) if and when the article is accepted for publication. The undersigned hereby transfers any and all rights in and to the paper including without limitation all copyrights to UMB. The undersigned hereby represents and warrants that the paper is original and that he/she is the author of the paper, except for material that is clearly identified as to its original source, with permission notices from the copyright owners where required. The undersigned represents that he/she has the power and authority to make and execute this assignment.
We declare that:
1. This paper has not been published in the same form elsewhere.
2. It will not be submitted anywhere else for publication prior to acceptance/rejection by this Journal.
3. A copyright permission is obtained for materials published elsewhere and which require this permission for reproduction.
Furthermore, I/We hereby transfer the unlimited rights of publication of the above mentioned paper in whole to UMB. The copyright transfer covers the exclusive right to reproduce and distribute the article, including reprints, translations, photographic reproductions, microform, electronic form (offline, online) or any other reproductions of similar nature.
The corresponding author signs for and accepts responsibility for releasing this material on behalf of any and all co-authors. This agreement is to be signed by at least one of the authors who have obtained the assent of the co-author(s) where applicable. After submission of this agreement signed by the corresponding author, changes of authorship or in the order of the authors listed will not be accepted.
Retained Rights/Terms and Conditions
1. Authors retain all proprietary rights in any process, procedure, or article of manufacture described in the Work.
2. Authors may reproduce or authorize others to reproduce the Work or derivative works for the authors personal use or for company use, provided that the source and the UMB copyright notice are indicated, the copies are not used in any way that implies UMB endorsement of a product or service of any employer, and the copies themselves are not offered for sale.
3. Although authors are permitted to re-use all or portions of the Work in other works, this does not include granting third-party requests for reprinting, republishing, or other types of re-use.
