DESAIN KOMPONEN UTAMA ALAT UJI KONSTANTA PEGAS UNTUK KAPASITAS 50 N/MM
DOI:
https://doi.org/10.22441/jtm.v10i1.11108Keywords:
Alat uji konstanta pegas, pegas, simulasi, faktor keamananAbstract
Pegas pada umumnya mempunyai nilai konstanta yang tidak diketahui sehingga menyulitkan dalam pemilihan penggunaan pegas. Alat uji konstanta pegas menggunakan spesimen berupa pegas ulir tekan dengan sistem manual hidrolik dalam bentuk alat bottle jack, hal ini digunakan sebagai penekan bahan uji (pegas ulir tekan). Penelitan ini bertujuan untuk mendesain dan mensimulasikan alat uji konstanta pegas dengan faktor keamanan yang tepat dengan kapasitas beban pegas 50N/mm. Metode yang digunakan dengan perhitungan manual lalu disimulasikan pada bagian utama komponen yang berhubungan dengan pengujian bahan pegas ulir tekan menggunakan perangkat lunak Solidwork. Dari hasil simulasi tersebut dapat dikatakan desain rangka kuat menahan beban statis maksimumnya sebesar 2000N atau 203,94 kgf dengan faktor keamanan sebesar 1,1 yang bisa dikatakan aman, jika dipakai dalam keadaan normalnya.Downloads
References
. Gere, J. M. (2008). Mechanics of Materials. 6th ed. In Book. https://doi.org/10.1016/j.mechmat.2009.01.011
. Jadhav, A. R., Pol, G. J., & Desai, A. A. (2015). Design and Manufacturing of Hydraulic Spring Stiffness Testing Machine. 4395(October 2014), 184–190.
. Martias, H. D. (2018). Perancangan Dan Pembuatan Alat Uji Defleksi Pegas Spiral. 1, 1–7.
. Mott, R. (2004). Timur 1. Elemen-elemen Mesin Dalam Perancangan Mekanis.
. Naik, S., & Kumbhalkar, S. B. J. S. S. (2018). Design & Analysis of Helical Spring Testing Machine : A Review. 6(01), 1059–1060.
. Yunus, A. D. (2010). Diktat mekanika kekuatan material.
. Khurmi RS Gupta, JK., (2005). Text Book of Machine Design Eurasia, Publising House, ltd Ram Nagar, New Delhi
. Shigley, Joseph E., dan Larry D. Mitchell. (1983). Perencanaan Teknik Mesin Edisi Keempat (Gandhi Harahap, Penerjemah). Jakarta. Erlangga
. Sularso, Kiyokatsu Suga, (2004). Dasar Perencanaan dan Pemilihan Elemen Mesin. Jakarta: Pradya Paramita
. Childs, Peter R. N., (2004). Mechanical Design, 2nd ed, Elsevier.
. Binsar Hariandja (1996). Mekanika teknik: statika dalam analisis struktur berbentuk rangka. Jakarta. Erlangga
Downloads
Published
How to Cite
Issue
Section
License
The copyright to this article is transferred to Universitas Mercu Buana (UMB) if and when the article is accepted for publication. The undersigned hereby transfers any and all rights in and to the paper including without limitation all copyrights to UMB. The undersigned hereby represents and warrants that the paper is original and that he/she is the author of the paper, except for material that is clearly identified as to its original source, with permission notices from the copyright owners where required. The undersigned represents that he/she has the power and authority to make and execute this assignment.
We declare that:
1. This paper has not been published in the same form elsewhere.
2. It will not be submitted anywhere else for publication prior to acceptance/rejection by this Journal.
3. A copyright permission is obtained for materials published elsewhere and which require this permission for reproduction.
Furthermore, I/We hereby transfer the unlimited rights of publication of the above mentioned paper in whole to UMB. The copyright transfer covers the exclusive right to reproduce and distribute the article, including reprints, translations, photographic reproductions, microform, electronic form (offline, online) or any other reproductions of similar nature.
The corresponding author signs for and accepts responsibility for releasing this material on behalf of any and all co-authors. This agreement is to be signed by at least one of the authors who have obtained the assent of the co-author(s) where applicable. After submission of this agreement signed by the corresponding author, changes of authorship or in the order of the authors listed will not be accepted.
Retained Rights/Terms and Conditions
1. Authors retain all proprietary rights in any process, procedure, or article of manufacture described in the Work.
2. Authors may reproduce or authorize others to reproduce the Work or derivative works for the authors personal use or for company use, provided that the source and the UMB copyright notice are indicated, the copies are not used in any way that implies UMB endorsement of a product or service of any employer, and the copies themselves are not offered for sale.
3. Although authors are permitted to re-use all or portions of the Work in other works, this does not include granting third-party requests for reprinting, republishing, or other types of re-use.
This work is also licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
