Tekstur dan Uji Tarik Paduan Ti~4%beratAl yang Dicanai Silang
DOI:
https://doi.org/10.22441/jtm.v7i3.3933Keywords:
Canai silang, Tekstur, Gambar Kutub, Uji tarikAbstract
Telah dilakukan pengukuran tekstur dan uji tarik paduan Ti~4%beratAl. Pengukuran tekstur dilakukan dengan teknik difraksi sinar-x menggunakan metode refleksi yang dinyatakan dengan gambar kutub (0002). Gambar kutub (0002) diperoleh dari cuplikan paduan Ti~4%beratAl yang dicanai silang pada suhu 600°C dengan reduksi tebal 96%. Kemudian cuplikan tersebut dianil pada suhu 900°C selama 31 jam. Selanjutnya cuplikan tersebut dilakukan uji tarik arah canai, 45o dan lintang. Hasil yang diperoleh menunjukan bahwa tektur Ti~4%beratAl yang dicanai silang memiliki tekstur basal dan sumbu-c sejajar arah normal. Anisotropi uji tarik pada cuplikan paduan Ti~4%beratAl yang dicanai pada suhu 600oC dan dianil pada suhu 900°C selama 31 jam tidak begitu terlihat.Downloads
References
Supriyanto, A. A. 2017. Pengaruh Suhu dan Waktu Anil terhadap Tekstur Paduan Al TIPE 2024. Jurnal SIMETRIS, Vol 8 (1): 61 – 66.
Supriyanto, A. A. dan Kurnia, D. 2016. Pengaruh Rekristalisasi pada Gambar Kutub (0002) Paduan Ti~4%beratAl. Jurnal Momentum, Vol. 18(1): 47 – 52.
Supriyanto, A. A.. 2017. Pengaruh Waktu Pengadukan terhadap Ukuran Kristalit dan Hambatan Jenis Al-Ti Menggunakan Tekni Pemaduan Mekanik. Jurnal Teknik Mesin (JTM): Vol. 06 (4): 220 – 224.
Tri Hardi Priyanto. 2009. Analisi Tekstur Tembaga dengan Teknik Difraksi Neutron. Jurnal Sains Materi Indonesia (Indonesian Journal of Materials Science) Vol. 11 (1): 52 – 56
Mukhopadhyay, P and Verma, A. K. 2010. Development of Cube Recrystallisation Texture and Microstructure of an Aluminium Alloy Suitable for Cartridge Case Manufacturing. Defence Science Journal 60(3): 330 – 336.
Hernández Rivera, J.L., Cruz Rivera, J.J., Paz del Ángel, V., Garibay Febles, V., Coreño Alonso, O. and Martínez-Sánchez, R. 2012. Structural and morphological study of a 2024 Al–Al2O3 composite produced by mechanical alloying in high energy mill. Materials and Design 37 (2012) 96–101.
Hafeez Ahamed and Senthilkumar, V. 2010. Role of nano-size reinforcement and milling on the synthesis of nano-crystalline aluminium alloy composites by mechanical alloying.Journal of Alloys and Compounds 505: 772–782.
Downloads
Published
How to Cite
Issue
Section
License
The copyright to this article is transferred to Universitas Mercu Buana (UMB) if and when the article is accepted for publication. The undersigned hereby transfers any and all rights in and to the paper including without limitation all copyrights to UMB. The undersigned hereby represents and warrants that the paper is original and that he/she is the author of the paper, except for material that is clearly identified as to its original source, with permission notices from the copyright owners where required. The undersigned represents that he/she has the power and authority to make and execute this assignment.
We declare that:
1. This paper has not been published in the same form elsewhere.
2. It will not be submitted anywhere else for publication prior to acceptance/rejection by this Journal.
3. A copyright permission is obtained for materials published elsewhere and which require this permission for reproduction.
Furthermore, I/We hereby transfer the unlimited rights of publication of the above mentioned paper in whole to UMB. The copyright transfer covers the exclusive right to reproduce and distribute the article, including reprints, translations, photographic reproductions, microform, electronic form (offline, online) or any other reproductions of similar nature.
The corresponding author signs for and accepts responsibility for releasing this material on behalf of any and all co-authors. This agreement is to be signed by at least one of the authors who have obtained the assent of the co-author(s) where applicable. After submission of this agreement signed by the corresponding author, changes of authorship or in the order of the authors listed will not be accepted.
Retained Rights/Terms and Conditions
1. Authors retain all proprietary rights in any process, procedure, or article of manufacture described in the Work.
2. Authors may reproduce or authorize others to reproduce the Work or derivative works for the authors personal use or for company use, provided that the source and the UMB copyright notice are indicated, the copies are not used in any way that implies UMB endorsement of a product or service of any employer, and the copies themselves are not offered for sale.
3. Although authors are permitted to re-use all or portions of the Work in other works, this does not include granting third-party requests for reprinting, republishing, or other types of re-use.
This work is also licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
