Vol 7, No 3 (2018)

Chief Editor

Muhamad Fitri ST, M.Si, Ph. D, Universitas Mercu Buana, Indonesia

Editorial Board

Prof. Dr. Ir. Chandrasa Soekardi, Universitas Mercu Buana, Indonesia
Dr. Kontan Tarigan, Universitas Mercu Buana, Indonesia
Dr. Nurdin Ali, Universitas Syiah Kuala, Indonesia
Dr. Poempida Hidayatulloh, Universitas Mercu Buana, Indonesia
Prof. Dr. Bambang Suharno, Universitas Indonesia, Indonesia
Dr.-Ing. Pudji Untoro, Universitas Surya, Indonesia
Dr.-Ing. Ir. Kusnanto Kusnanto, Universitas Gadjah Mada, Indonesia
Dr. Sagir Alva, Universitas Mercu Buana, Indonesia
Dr. Abdul Hamid, Universitas Mercu Buana

Editorial Staff

Bakri Rio Rahayu, Universitas Mercu Buana, Indonesia
Yananto Mihadi Putra, Universitas Mercu Buana, Indonesia
Goffari Maulana, Universitas Mercu Buana, Indonesia

Managing Editor

Ir. Haris Wahyudi, M.Sc, Universitas Mercu Buana, Indonesia
Muhamad Fitri, ST, MSi, PhD. Universitas Mercu Buana, Indonesia

Notifications

Journal Content
Browse

Keywords Age Replacement,downtime, optimal perencanaan perawatan dan preventive maintenance Airfoil, Qblade, Turbin Angin, Daya Barcode id, PLC, Raspberry Pi, PLC with Barcode Integration COP Co-firing, Boiler Pulverizer Coal, Sawdust, Emisi gas buang Composite fibers, weaving pattern, reinforcement, mechanical test, ballistic test Efisiensi Kata kunci: exhaust gas temperature margin, air mode, high pressure compressor clearance control Kendaraan listrik, baterai, service life, pengisian baterai, pengosongan baterai. Kursi Plastik MRT Jakarta Panel Surya Programable Logic Controller (PLC), Infrared Refrigeran, ODP, GWP, R22 Safety Factor Schedule Oil Sampling, Sistem Pelumasan, Diesel Engine, FMEA Shaft,Material,CAD egg incubator, tenaga surya, photovoltaic, unggas emergency landing loads fiber diameter, morphology, mechanical characteristics, tensile strength, Young’s modulus floor support structure

Aims and Scope
Peer Review Policy
Author Guidelines
Editorial Board
Abstracting & Indexing
Publication Ethics
Open Access Statement
Plagiarism Policy
Copyright and License
Article Processing Charge
Contact Us

Language

User

Font Size

Current Issue

Vol 7, No 3 (2018)

Table of Contents

Articles

Tekstur dan Uji Tarik Paduan Ti~4%beratAl yang Dicanai Silang

10.22441/jtm.v7i3.3933

Adolf Asih Supriyanto, Emmanuel Agung Nugroho

103-107

Empirical Model of Bearing Temperature Saturation at Asahan II Hydro-Turbine-Generator

10.22441/jtm.v7i3.4006

Bagus Brahmantya Gautama

108-112

Comparison Analysis of Quality of Ax-7 Advance Shelling Lubricants and Pertamina Enduro Racing Lubricants on Kawasaki Ninja 250cc Injeksi Motor

10.22441/jtm.v7i3.4033

Theo Agytha Putra

113-118

Studi Hasil Pengelasan Mahasiswa Semester 6 Konsentrasi Teknik Produksi Jurusan Teknik Mesin Politeknik Negeri Medan Untuk Posisi Pengelasan Pipa Pa Dan HLO45

10.22441/jtm.v7i3.4365

Melvin Bismark Hamonangan Sitorus, Piktor Tarigan, Udur 1 Januari Hutabarat

119-124

Inovasi dan Optimasi Metode Pirolisis Material Karbon berbasis Serat Bulu Ayam untuk Aplikasi Material Penyimpan Hidrogen

10.22441/jtm.v7i3.5002

Deni Shidqi Khaerudini

125-130

Penggunaan Saluran Untuk Meningkatkan Unjuk Kerja Model Sistem Pembangkit Listrik Ultra Low Head

10.22441/jtm.v7i3.4574

Jorfri Boike Sinaga, Ahmad Suudi, Okta Syahputra Sembiring, Rizki Zakaria Manalu

131-137

Analisis Pengaruh Ketidakstabilan Temperatur Terhadap Hasil Kekerasan Meterial dari Proses Heat Treatment Piston

10.22441/jtm.v7i3.4520

Nandar Saliro Wibowo, Nurato Nurato

138-148

Analisis PHE (Potensi Hemat Energi) dan Pengembangan Software Efisiensi Energi Pada Rumah Sakit Ba, Tangerang

10.22441/jtm.v7i3.5255

Agung Wahyudi Biantoro

149-156

Jurnal Teknik Mesin (JTM)
Program Studi Teknik Mesin, Fakultas Teknik, Universitas Mercu Buana
Jl. Meruya Selatan No. 01, Kembangan, Jakarta Barat 11650, Indonesia
Email: [email protected]
Telp.: 021-5840815/ 021-5840816 (Hunting)
Fax.: 021-5871335

JTM is indexed by the following abstracting and indexing services:

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.