PEMANFAATAN LIMBAH SiC UNTUK MEMPERBAIKI KEKUATAN IMPAK ALUMINIUM SCRAP DAN STRUKTUR MIKRONYA DENGAN METODE SINTERING
DOI:
https://doi.org/10.22441/jtm.v8i1.4882Keywords:
SiC, Al-scrap, Sintering, Impact toughnessAbstract
Abstrak-- Penelitian ini bertujuan mengetahui pengaruh penambahan limbah silikon karbida (SiC) pada aluminium scrap (Al-scrap) terhadap ketangguhan impak dan setruktur mikro dengan metode metalugi serbuk (sintering). Material yang digunakan pada penelitian ini adalah Al-scrap dan SiC. Ada tiga variasi campuran yaitu campuran cetakan masing-masing 0, 10 dan 20 % SiC. Pemanasan dilakukan selama 3 jam dan suhu 500 Co. Pengujian yang dilakukan adalah pengujian impak dan pengamatan struktur mikro.
Hasil penelitian menunjukan bahwa variasi dari penambahan SiC mempengaruhi kekuatan impak bahan. Penambahan SiC 20 % pada penelitian ini menghasilkan kekuatan impak yang paling tinggi sebesar 13.078 x 10-3 J/mm². Sedangkan Al-scrap tanpa penambahan SiC adalah 11.98 x 10-3 J/mm².
Katakunci: SiC, Al-scrap, Sintering, Ketangguhan impak
Abstract-- The study aims is to determine the effect of the additional of the silicon carbide (SiC) disposal to the aluminum scrap (Al-scrap) over the impact strength and microstructure by sintering method. The materials used in this study were Al-scrap and silicon carbide (SiC). There were three mixed variations, they were 0, 10 and 20% SiC. The specimens were heated for 3 hours at the temperature of 500 Co. The tests carried out were impact testing and microstructure observation. The results showed that the variations in the addition of SiC affected the value of the impact strength of the material. The addition of 20% SiC in this study resulted in the highest impact toughness of 13,08 x 10-3 J / mm². Whereas Al-scrap without the addition of SiC was 11.98 x 10-3 J / mm².
Keywords: SiC, Al-scrap, Sintering, Impact toughness
Downloads
References
. Amini H., Mashhadi A., Moloodi M., Golestanipour E.Z.V., Karimi (2009). Recycling of Aluminium Alloy Turning Scrap Via Cold Pressing and Melting With Salt Flux. Science Dirrect, Elsevier, Journal of materials processing technology 209: 3138–3142.
. Aqida S. (2004). Effects of Porosity on Mechanical Properties of Metal Matrix Composites: An Overview. Jurnal Teknologi Universiti Teknologi, Malaysia (UTM). 6(2): 46-53.
. Dieter G. (1988). Mechanical Metallurgy. Mc.Grow Hill Book Co.
. Downson G. (1990). Powder Metallurgy The Processing and its Product. Reddiffe Way. Bristol BS1 6NX. England.
. Grum J., Kisin M. (2006). The influence of the microstructure of three Al–Si alloys on the cutting-force amplitude during fine turning. Science Dirrect. Elsevier, International Journal of Machine Tools & Manufacture. 46: 769–781.
. Hartomo A.J. (1992). Memahami Polimer dan Perekat. Andi Offset. Edisi Pertama Yogyakarta.
. Heather L.F., and Nikki W.D. (2001). The Material Information Society, Toronto University Press.
. Jamaliah I. (2003). Kajian Sifat Kehausan dan Kekerasan Komposit Matriks Alumunium. Universiti Teknologi Malaysia.
. Johannes P., Kotzé (2013). Evaluation of a Latent Heat Thermal Energy Storage System Using AlSi12 as a Phase Change Material. Stellenbosch University Centre for Renewable and Sustainable Energy Studies, ASME, Journal of Solar Energy Engineering. 135: 23-31.
. Khairel R., Ahmad (2005). The Influence of Alumina Particle Size on SinteredDensity and Hardness of Discontinous Reinforced Aluminum Metal Matrix Composites. Universiti Teknologi Malaysia.
. Kiryanto, Eko S., Hadi, Ansori M., (2012). Analisa Sifat Mekanik Paduan Aluminium Sebagai Rangka Jendela Kapal di Perusahaan Pengecoran Logam CV. Setia Kawan Kota Tegal dengan Cetakan Tidak Permanen. Jurnal Kapal. 9(1): 11-19.
. Lasagni F, Marks E., Holzapfel C., Mu¨cklich F., Degischer H.P. (2007). Three Dimensional Characterization of „as-cast‟ and Solution-Treated AlSi12(Sr) Alloys by High Resolution FIB Tomography. Science Dirrect, Elsevier, Acta Materialia 55: 3875–3882.
. Manash D., Makhlouf M., (2001). Effect of key Alloying Elemnts on the Feeding Characteristics of Aliminium-Silicon Casting Alloys. Journal of Light Metals. 1: 251-265.
. Lee J.A.. (2003). Cast Aluminum Alloy for High Temperature Applications, The Minerals, Metals & Material Society, Toronto, Canada.
. Lutfi, Sukron (2010). Pengaruh Magnesium Terhadap Proses Elektroless Coating pada Partikel Penguat SiC. Departement Teknik Metalurgi dan Material Universitas Indonesia.
. Olivier B. (2002). Metal Matrix Composites (MMC’s), Empa, Swiss Federal Laboratories for Material Research and Testing. Dept Material and Technology. Swiss.
. Peter T.B. (1990). Engineering Properties of Carbides, Engineered Material Hand Book, vol 4, Ceramics and Glasess.
. Randall M., German R. (1991). Fundamental of Sintering, Ceramic and Glasses, Engineered Materials. Handbook. Volume 4. ASM International. USA.
. Saranavanan R.A. (1998). Dry Sliding Wear Behavior of A356-15 Pct SiCp Composites under Controlled Atmospheric Conditions, Metallurgical and Materials Transactions. Handbook, New Delhi Press.
. Scwartz M.l. (1984). Composite Material Handbook. McGraw Hill, Inc. New York, USA..
. Sciti D., Bellosi A. (2002). Microstructure and Properties of Alumina-SiC Nano Composites Prepared from Ultrafine Powders. Kluwer Academic Publishers.
. Surdia T., Saito S. (1995) Pengetahuan Bahan Teknik. PT. Pradnya Paramita, Jakarta.
. Widodo R. (2012). Teknik Pengelolaan Bahan Baku Peleburan Aluminium”, Jurnal Foundry Vol. 2 No. 1, ISSN : 2087-225.
. Zheng R., Sammy L., Ip C. (2000). Mechanical Properties of Nanometric Particulate Reinforced Aluminium Composites. School of Materials Science and Engineering, UNSW.
. Zhongliang S. (2001).The Oxidation of SiC Particle and Its Interfacial Characteristics in Al-Matrix Composites. Kluwer Academic Publisher.
Downloads
Additional Files
Published
How to Cite
Issue
Section
License
The copyright to this article is transferred to Universitas Mercu Buana (UMB) if and when the article is accepted for publication. The undersigned hereby transfers any and all rights in and to the paper including without limitation all copyrights to UMB. The undersigned hereby represents and warrants that the paper is original and that he/she is the author of the paper, except for material that is clearly identified as to its original source, with permission notices from the copyright owners where required. The undersigned represents that he/she has the power and authority to make and execute this assignment.
We declare that:
1. This paper has not been published in the same form elsewhere.
2. It will not be submitted anywhere else for publication prior to acceptance/rejection by this Journal.
3. A copyright permission is obtained for materials published elsewhere and which require this permission for reproduction.
Furthermore, I/We hereby transfer the unlimited rights of publication of the above mentioned paper in whole to UMB. The copyright transfer covers the exclusive right to reproduce and distribute the article, including reprints, translations, photographic reproductions, microform, electronic form (offline, online) or any other reproductions of similar nature.
The corresponding author signs for and accepts responsibility for releasing this material on behalf of any and all co-authors. This agreement is to be signed by at least one of the authors who have obtained the assent of the co-author(s) where applicable. After submission of this agreement signed by the corresponding author, changes of authorship or in the order of the authors listed will not be accepted.
Retained Rights/Terms and Conditions
1. Authors retain all proprietary rights in any process, procedure, or article of manufacture described in the Work.
2. Authors may reproduce or authorize others to reproduce the Work or derivative works for the authors personal use or for company use, provided that the source and the UMB copyright notice are indicated, the copies are not used in any way that implies UMB endorsement of a product or service of any employer, and the copies themselves are not offered for sale.
3. Although authors are permitted to re-use all or portions of the Work in other works, this does not include granting third-party requests for reprinting, republishing, or other types of re-use.
This work is also licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
