Application of Failure Mode and Effect Analysis (FMEA) for Defect Reduction: A Case Study on Scratch Defects in Oil Separator Parts in Machining Line
DOI:
https://doi.org/10.22441/ijiem.v4i3.22768Kata Kunci:
5S, Automotive parts, Effort and impact analysis, FMEA, QualityAbstrak
This study addresses the problem of significant defect rates on Oil Separator Parts in machining line, especially focusing on scratch defects. The defect rate reached 0.495%, exceeding the company's target of 0.1%. In the approach using FMEA, potential failure modes were identified and rated based on Risk Priority Number to plan corrective actions. Effort and Impact Analysis was used to analyze the most effective action recommendations. Implementation of the 5S methodology was selected as the improvement solution, which focused on workplace organization, maintenance, and cleanliness. The results were positive, with the number of defects decreasing dramatically from 540 to 67 units in July 2023, and the defect rate dropping from 0.495% to 0.145%. Although the company's quality targets have not been fully achieved, the FMEA approach and 5S implementation have been shown to significantly improve production quality and reduce defects. This study proves that this approach has the potential to address complex quality issues, although further challenges may be required to achieve the final goals set.Unduhan
Referensi
Dewi, S. R., Setiawan, B., & Susatyo Nugroho, W. P. (2013). 5S program to reduce change-over time on forming department (case study on CV Piranti Works temanggung). IOP Conference Series: Materials Science and Engineering, 46(1). https://doi.org/10.1088/1757-899X/46/1/012040
Febriana, T. H., Dewita, H., Hermawan, C., & Herlambang, H. (2020). Perbaikan Ketahanan Lifetime Bladder untuk Peningkatan Curing Efficiency pada Proses Industri Tire Manufacture. IJIEM - Indonesian Journal of Industrial Engineering and Management, 1(1), 33. https://doi.org/10.22441/ijiem.v1i1.9258
Iska Aprilia Wardhani, M., Nikmatullah Realita, T., Studi Manajemen, P., & Indocakti Malang, S. (2022). SOSMANIORA (Jurnal Ilmu Sosial dan Humaniora) 5S As a Form of Lean Manufacturing Implementation in the Perspective of Human Resources: A Case Study in Food SMEs. 1(4), 599–605. https://doi.org/10.55123/sosmaniora.v1i4.1275
Kholil, M. (2023). Lean Manufacturing Implementation to Reduce Reject on Part Step Floor with DMAIC and FMEA approach. 3(6), 11–19. https://doi.org/10.54756/IJSAR.2023.V3.6.2
Millenia, T. P., Muhammad, F., & Handoko, B. (2023). Implementation of the 5S Work Attitude Using the Lean Six Sigma Method to the Performance Productivity of Medical Records Unit Officers of Arifin Achmad Hospital, Riau Province. Journal of Health Sciences, 16(01), 43–50. https://doi.org/10.33086/jhs.v16i01.3701
Neves, P., Silva, F. J. G., Ferreira, L. P., Pereira, T., Gouveia, A., & Pimentel, C. (2018). Implementing Lean Tools in the Manufacturing Process of Trimmings Products. Procedia Manufacturing, 17, 696–704. https://doi.org/10.1016/j.promfg.2018.10.119
Novianti, F., & Rochmoeljati, R. (2023). Quality Control of Edamame Products Using Statistical Quality Control ( SQC ) and Failure Mode Effect Analysis ( FMEA ) Methods in PT. XYZ. Indonesian Journal of Industrial Engineering & Management, 4(2), 221–230. https://doi.org/10.22441/ijiem.v4i2.20550
Pérez-Pucheta, C. E., Olivares-benitez, E., & Minor-popocatl, H. (2019). Implementation of Lean Manufacturing to Reduce the Delivery Time of a Replacement Part to Dealers : A Case Study. Applied Sciences, 9(3932), 1–23.
Shahriar, M. M., Parvez, M. S., Islam, M. A., & Talapatra, S. (2022). Implementation of 5S in a plastic bag manufacturing industry: A case study. Cleaner Engineering and Technology, 8(April), 100488. https://doi.org/10.1016/j.clet.2022.100488
Sharma, S. S., Shukla, D. D., & Sharma, B. P. (2019). Analysis of lean manufacturing implementation in SMEs: A “5S” technique. In Lecture Notes in Mechanical Engineering. Springer Singapore. https://doi.org/10.1007/978-981-13-6412-9_46
Solihudin, M., Nurhidayat, W., Suwandi, S., Bakti, C. S., Rachmat, R., Hadi, A. H., & Nugroho, S. (2023). Implementation of Tree Diagram Method, Failure Mode Effect Analysis (FMEA) and 5W 1H to Reduce Corky Defective Products in PT. XYZ. IJIEM - Indonesian Journal of Industrial Engineering and Management, 4(1), 18. https://doi.org/10.22441/ijiem.v4i1.17237
Sumasto, F., Akbar, M. R., Fajri, S., & Husna, H. (2023). Peningkatan Value Added dalam Industri Tahu melalui Penerapan Lean Manufacturing dan Analisis Waste. Jurnal Serambi Engineering, VIII(4), 7338–7347. https://doi.org/10.32672/jse.v8i4.6876
Sumasto, F., Arliananda, D. A., Imansuri, F., Aisyah, S., & Pratama, I. R. (2023). Fault Tree Analysis: A Path to Improving Quality in Part Stay Protector A Comp. Journal Européen Des Systèmes Automatisés, 56(05), 757–764. https://doi.org/10.18280/jesa.560506
Sumasto, F., Arliananda, D. A., Imansuri, F., Aisyah, S., & Purwojatmiko, B. H. (2023). Enhancing Automotive Part Quality in SMEs through DMAIC Implementation : A Case Study in Indonesian Automotive Manufacturing. Quality Innovation Prosperity, 27(3), 57–74. https://doi.org/10.12776/QIP.V27I3.1889
Sumasto, F., Maharani, C. P., Purwojatmiko, B. H., Imansuri, F., & Aisyah, S. (2023). PDCA Method Implementation to Reduce the Potential Product Defects in the Automotive Components Industry. Indonesian Journal of Industrial Engineering & Management, 4(2), 87–98. https://doi.org/10.22441/ijiem.v4i2.19527
Sumasto, F., Nugroho, Y. A., Purwojatmiko, B. H., Wirandi, M., Imansuri, F., & Aisyah, S. (2023). Implementation of Measurement System Analysis to Reduce Measurement Process Failures on Part Reinf BK6. Indonesian Journal of Industrial Engineering & Management, 4(2), 212–220. https://doi.org/10.22441/ijiem.v4i2.20212
Sumasto, F., Riyanto, A., Pratama, I. R., Imansuri, F., & Putri, A. (2023). Meningkatkan Produktivitas di Sektor Otomotif ( Studi Kasus : Yanto ’ s Truck Seat Service ). Jurnal Serambi Engineering, VIII(4), 7356–7369. https://doi.org/10.32672/jse.v8i4.6898
Sumasto, F., Safril, S., Imansuri, F., & Wirandi, M. (2022). Penerapan Manajemen Kualitas Terpadu Pada Industri Makanan Skala Mikro, Kecil Dan Menengah (Studi Kasus Umkm Nasi Goreng). Jurnal PASTI (Penelitian Dan Aplikasi Sistem Dan Teknik Industri), 16(3), 274. https://doi.org/10.22441/pasti.2022.v16i3.003
Sumasto, F., Satria, P., & Rusmiati, E. (2022). Implementasi Pendekatan DMAIC untuk Quality Improvement pada Industri Manufaktur Kereta Api. Jurnal INTECH Teknik Industri Universitas Serang Raya, 8(2), 161–170. https://doi.org/doi.org/10.30656/intech.v8i2.4734
Suresh Kumar, B., & Syath Abuthakeer, S. (2012). Implementation of lean tools and techniques in an automotive industry. Journal of Applied Sciences, 12(10), 1032–1037. https://doi.org/10.3923/jas.2012.1032.1037
Tarigan, U. P. P., & Budiman, I. (2021). Implementasi Metode Lean Service dan 5S untuk Meningkatkan Efisiensi Waktu Pelayanan di Dinas Pencegah dan Pemadam Kebakaran Kota Medan. Jurnal Sistem Teknik Industri, 23(1), 59–68. https://doi.org/10.32734/jsti.v23i1.4891
Wahjudi, D., & Cahyadi, A. (2022). Implementasi FMEA untuk Peningkatan Produktifitas di PT. X. Jurnal Teknik Mesin, 19(2), 45–50. https://doi.org/10.9744/jtm.19.2.45-50
Wahjudi, D., & Projesa, Y. D. P. (2021). An FMEA-Based Approach to Waste Reduction A Case on a Make-to-Order Company. Proceedings of the International Conference on Business and Engineering Management (ICONBEM 2021), 177, 7–11. https://doi.org/10.2991/aebmr.k.210522.002
Zuniawan, A. (2020). A Systematic Literature Review of Failure Mode and Effect Analysis (FMEA) Implementation in Industries. IJIEM - Indonesian Journal of Industrial Engineering and Management, 1(2), 59. https://doi.org/10.22441/ijiem.v1i2.9862
Unduhan
Diterbitkan
Cara Mengutip
Terbitan
Bagian
Lisensi
The copyright to this article is transferred to Universitas Mercu Buana (UMB) if and when the article is accepted for publication. The undersigned hereby transfers any and all rights in and to the paper including without limitation all copyrights to UMB. The undersigned hereby represents and warrants that the paper is original and that he/she is the author of the paper, except for material that is clearly identified as to its original source, with permission notices from the copyright owners where required. The undersigned represents that he/she has the power and authority to make and execute this assignment.
We declare that:
1. This paper has not been published in the same form elsewhere.
2. It will not be submitted anywhere else for publication prior to acceptance/rejection by this Journal.
3. A copyright permission is obtained for materials published elsewhere and which require this permission for reproduction.
Furthermore, I/We hereby transfer the unlimited rights of publication of the above mentioned paper in whole to UMB. The copyright transfer covers the exclusive right to reproduce and distribute the article, including reprints, translations, photographic reproductions, microform, electronic form (offline, online) or any other reproductions of similar nature.
The corresponding author signs for and accepts responsibility for releasing this material on behalf of any and all co-authors. This agreement is to be signed by at least one of the authors who have obtained the assent of the co-author(s) where applicable. After submission of this agreement signed by the corresponding author, changes of authorship or in the order of the authors listed will not be accepted.
Retained Rights/Terms and Conditions
1. Authors retain all proprietary rights in any process, procedure, or article of manufacture described in the Work.
2. Authors may reproduce or authorize others to reproduce the Work or derivative works for the authors personal use or for company use, provided that the source and the UMB copyright notice are indicated, the copies are not used in any way that implies UMB endorsement of a product or service of any employer, and the copies themselves are not offered for sale.
3. Although authors are permitted to re-use all or portions of the Work in other works, this does not include granting third-party requests for reprinting, republishing, or other types of re-use.
