Implementasi metode NIOSH dan Analisa QEC pada alat potong ranting
DOI:
https://doi.org/10.22441/pasti.2019.v13i2.002Kata Kunci:
QEC, NIOSH, ErgonomiAbstrak
Abstrak Penelitian ini merupakan penciptaan teknologi baru yang sederhana dengan merekayasa sistem hidrolik dan prinsip genggaman tangan yang difungsikan sebagai alat pemotong ranting adjustable (dapat diatur panjang pendeknya) yang ergonomi, dengan panjang normal 1,5 meter, maksimal 3 meter. Berat 2,8 kg, panjang jangkauan genggaman 94 mm dan diameter gagang 52 mm. Penelitian ini menggunakan metode analisa ergonomi untuk mengetahui kesesuaian alat dengan manusia yaitu dengan pengambilan 95 persentil. Di dapat diameter genggaman tangan 54, 29 mm sedangkan untuk lebar telapak tangan adalah 97,87 mm, tekanan maksimal yang diperlukan untuk memotong ranting adalah 234,39 kg/cm2 dengan diameter 5 mm yaitu jenis ranting kakao. Sedangkan dengan analisa NIOSH didapat berat yang disyaratkan adalah 4,89 Kg, kemudian dengan metode QEC didapat level presentase skornya paling tinggi adalah 47,62. artinya diperlukan perbaikan untuk alat tersebut dalam waktu kedepan. Untuk pembebanan kerja agar tidak letih dengan waktu kerja 8,40 menit dan istirahat 7,14 menit.Hasil penelitian menyimpulkan bahwa alat tersebut masih harus diperbaiki dalam waktu kedepan, sedangkan penggunaannya cukup singkat dan hanya difungsikan untuk pamanenan cengkeh saja serta pemanenan yang lain yang sejenis dengan diameter maksimal (1 cm) saja. Kata kunci - QEC, NIOSH, ErgonomiUnduhan
Referensi
Ahmad Zaelani, Cucu Cunayah, Etsa Indra Irawan (2006),”Bimbingan pemantapan fisika untuk SMA/MA”, Yrama widya. Bandung.
Anonim, 1998, “Buku Panduan Kehutanan Indonesia. Badan Penelitian dan Pengembangan Kehutanan dan Perkebunan”. Jakarta.
______ , 1998, “Pedoman Pembangunan Hutan Tanaman Industri”, Departemen Kehutanan Badan Penelitian dan Pengembangan Kehutanan. Jakarta.
______ , 2004, “Pembangunan Hutan Tanaman Acacia mangium Pengalaman di PT.Musi Hutan Persada, Sumatera Selatan”, Polydoor Yogyakarta.
Bambang Triatmodjo(1993), “Hidraulika II”, Yogyakarta: Beta Offset
Brown S. (1997),“Estimating biomasas change of tropical forest”, a primer. FAO Forestry paper 134,FAO, Rome.
Daniel, Th.W.,John Helms dan F.S.Baker, (1987),”Prinsip-Prinsip Silvikutur” Gadjah Mada University Press, Yogyakarta.
Dwi Ayu Mulia Sari, (2008),“Analisa Pengaruh postur tangan dan jenis kelamin terhadap tingkat getaran, waktu reaksi pengereman, dan kekuatan genggam”Skripsi, TI-FTMI,FT-UGM.
Evans, (1982),”Plantation Forestry in The Tropics”,Clarendon Press Oxford.
Grandjean, E. (1986). Fitting the Task to the Man. 4th ed. Taylor & Francis Inc. London.
Kroemer, K.H.E. (1994). Ergonomics: How to Design for Ease and Efficiency. New Jersey: Prentice-Hall, Inc.
Li, G. dan Buckle,P. (1999). “Current Teechniques for assessing Physical Exposure to Work-Related Musculuskeletal Risk, with Emphasis on Posturew-Based Methods”, Ergonomics, 42(5): 674-695
Nurmianto, E. (1991 b), “Desain stasiun kerja industri” : Tinjauan ergonomi dalam industri. Seminar Nasional Desain Produk Industri, FTSP-FTI ITS, Surabaya.
Nurmianto, E (2003),”Ergonomi, Konsep dasar dan aplikasinya”,Guna widaya, ITS, Surabaya.
Pheasant, S. (1986),”Body space : anthropometry, ergonomics and design” London: Taylor and Francis.
Purnomo, Dwi Edi, Mayor Infantri (1991),”Studi Ergonomi pada bentuk pistol P-1 9 mm buatan PT. PINDAD”. Tugas mata kuliah Ergonomi, TMNI-XII, STTAL- KODIKAL, Surabaya.
Riduwan, Drs.,M.B.A., Prof.Dr. Akdon, M.Pd (2007),”Rumus dan data dalam Analisis Statistika”Alfabeta, Bandung.
Sunardi. B. S. P. (1977),”Ilmu kayu”,Yayasan pembina fakultas kehutanan UGM Yogyakarta.
Stevenson.M.G. (1989),“Lecture notes the principles of ergonomics”,center for safety science, Univ. Of New South Wales, Sydney.
T.A.Prayitno, (1995).Terjemahan,”Pengujian sifat fisika dan mekanika menurut ISO”, Fakultas Kehutanan Universitas Gadjah Mada, Yogyakarta.
Tarwaka, Solichul HA.Bakri, Lilik Sudiajeng, (2004),”Ergonomi untuk Kesehatan, Keselamatan Kerja dan Produksivitas”, UNIBA PRESS, Surakarta, Indonesia.
Thomas Krist, Dr.Ing. (1991),” Hidarulika”, Erlangga
Van Noordwijk, (1999). Functional Branch Analysis to derive alometrik equations of trees. In:Murdyarso D, Van Noordwijk M and Suyamto D A (eds.) Modelling Global Change Impactson the Soil Environment. IC-SEA Report No 6: 77-79.
Wagaurd, Frederick, (1950),”The mechanical properties of wood”, John wiley & sons, Inc. New York, Chapmen Q hell, limited, London.
Yustadi Y CE, (1986),” Seri penyelesaian- Mekanika Fluida ”Cipta Offset
Unduhan
Diterbitkan
Cara Mengutip
Terbitan
Bagian
Lisensi
The copyright to this article is transferred to Universitas Mercu Buana (UMB) if and when the article is accepted for publication. The undersigned hereby transfers any and all rights in and to the paper including without limitation all copyrights to UMB. The undersigned hereby represents and warrants that the paper is original and that he/she is the author of the paper, except for material that is clearly identified as to its original source, with permission notices from the copyright owners where required. The undersigned represents that he/she has the power and authority to make and execute this assignment.
We declare that:
1. This paper has not been published in the same form elsewhere.
2. It will not be submitted anywhere else for publication prior to acceptance/rejection by this Journal.
3. A copyright permission is obtained for materials published elsewhere and which require this permission for reproduction.
Furthermore, I/We hereby transfer the unlimited rights of publication of the above mentioned paper in whole to UMB. The copyright transfer covers the exclusive right to reproduce and distribute the article, including reprints, translations, photographic reproductions, microform, electronic form (offline, online) or any other reproductions of similar nature.
The corresponding author signs for and accepts responsibility for releasing this material on behalf of any and all co-authors. This agreement is to be signed by at least one of the authors who have obtained the assent of the co-author(s) where applicable. After submission of this agreement signed by the corresponding author, changes of authorship or in the order of the authors listed will not be accepted.
Retained Rights/Terms and Conditions
1. Authors retain all proprietary rights in any process, procedure, or article of manufacture described in the Work.
2. Authors may reproduce or authorize others to reproduce the Work or derivative works for the authors personal use or for company use, provided that the source and the UMB copyright notice are indicated, the copies are not used in any way that implies UMB endorsement of a product or service of any employer, and the copies themselves are not offered for sale.
3. Although authors are permitted to re-use all or portions of the Work in other works, this does not include granting third-party requests for reprinting, republishing, or other types of re-use.
