DESIGN OF FRAME FOR THE PUMP PERFORMANCE TEST EQUIPMENT USING VDI 2221 METHOD

Muhamad Fitri, Frelly Rizqiansyah

Abstract


Pumps in modern human life have become a major need, and their use is very wide, therefore pump learning is indispensable for mechanical engineering students. For pump performance learning media, Pump Performance Test Equipment (PPTE) is needed. The test equipment requires a strong frame and meets the requirements to be able to withstand the load, not only the equipment load but also the water weight used as the working fluid on the performance test equipment which is very large. This study aims to design a frame that can withstand the entire load of the PPTE. The design is done by calculating the load experienced by the frame when the test equipment is operated. The design of this pump performance test framework uses the VDI 2221 method, which includes several stages: task clarification, design concepts, concept embodiment, and design details. The results obtained from the use of the VDI 2221 method are variation 1, with a frame of 1000mm length, 1200mm width, and 1140mm height. The frame specifications using 4x4 hollow steel size with a thickness of 2mm and 4x6 size with a thickness of 3mm, and using a wheel type with a lock that can withstand the load. maximum up to 600kg.

Keywords


PPTE; Frame; VDDI 2221

Full Text:

PDF

References


A. Supendi and M. Fitri, “Pemilihan Spesifikasi Komponen Alat Uji Prestasi Pompa Menggunakan Metode Analisis Persamaan Bernoulli” Jurnal Teknik Mesin, vol. 11, no. 1, p. 42, 2022.

A. Basri and M. Fitri, “Perancangan Alat Uji Prestasi Pompa Menggunakan Metode VDI 2221” Jurnal Teknik Mesin, vol. 10, no. 3, p. 126, 2021.

Z. Pratama, “Desain Komponen Utama Alat Uji Konstanta Pegas Untuk Kapasitas 50 N/Mm,” J. Tek. Mesin, vol. 10, no. 1, p. 15, 2021.

H. Pranoto, M. Fitri, and A. F. Sudarma, “Analisis Statik Pelat Penyambung pada Ladder Frame Chassis Untuk Kendaraan Pedesaan Dengan Menggunakan Metode Elemen Hingga,” Rotasi, vol. 23, no. 1, pp. 18–23, 2021.

A. Pratama and M. Fitri, “Rancang Bangun Alat Uji Konstanta Pegas Untuk Kapasitas 50 N/Mm Menggunakan Metode VDI 2221,” AME (Aplikasi Mek. dan Energi) J. Ilm. Tek. Mesin, vol. 6, no. 2, p. 41, 2020.

A. Digdoyo and D. Djamruddin, “Performa Alat Uji Pompa Sentrifugal Pada Putaran 1200 RPM dan 800 RPM,” pp. 1–7, 2020.

M. Munasir, “Studi Pengaruh Orientasi Serat Fiber Glass Searah dan Dua Arah Single Layer terhadap Kekuatan Tarik Bahan Komposit Polypropylene,” J. Penelit. Fis. dan Apl., vol. 1, no. 1, p. 33, 2011.

R. Harfi and U. M. Sugeng, “Analisa Biaya Dan Perancangan Alat Pemasang Bushing Pada Attachment Pc 400 Dengan Metode VDI,” vol. 2, no. 2, pp. 47–54, 2015.

U. Panjaitan, “Perancangan Mesin Pencacah Rumput Multifungsi Dengan Metode VDI 2221,” Presisi, vol. 22, no. 1, pp. 65–78, 2020.

J. Jänsch and H. Birkhofer, “The development of the guideline VDI 2221 - The change of direction,” 9th Int. Des. Conf. Des. 2006, pp. 45–52, 2006.




DOI: http://dx.doi.org/10.22441/ijimeam.v4i1.15374

Refbacks

  • There are currently no refbacks.


Copyright (c) 2022 Muhamad Fitri, Frelly Rizqiansyah

Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

INDEXED IN

 

 

Publisher Address:
Universitas Mercu Buana
Program Studi S2 Teknik Mesin
Jl. Meruya Selatan No. 1, Jakarta 11650, Indonesia
Phone/Fax. (+6221) 5871335
Email [email protected]
Homepage http://teknikmesin.ft.mercubuana.ac.id/

Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.