Numerical Analysis of Heat Transfer Enhancement in Wavy Trapezoidal and Rectangular Microchannels

Soumik Kumar Hazra

Abstract


This study presents a comprehensive numerical investigation of heat transfer enhancement in microchannels with varying geometries, specifically focusing on wavy microchannels with trapezoidal and rectangular cross-sections. Water is used as the working fluid, and silicon is selected as the solid wall material. A three-dimensional conjugate heat transfer model is developed by solving the steady-state Navier–Stokes and energy equations using the finite volume method in ANSYS Fluent, with the SIMPLEC algorithm employed for pressure–velocity coupling. The analysis examines the influence of cross-sectional shape and wall waviness on thermal performance, while maintaining a constant hydraulic diameter across all configurations. Eight different geometries, including smooth and wavy versions of rectangular and trapezoidal cross-sections with varying top-to-bottom width ratios (0.075–0.055 mm), are evaluated over a Reynolds number range corresponding to inlet velocities of 0.5–4.0 m/s. Results show that wavy microchannels significantly enhance heat transfer compared to their smooth counterparts. For instance, at 4 m/s, the Nusselt number for the wavy rectangular microchannel reaches 9.48, compared to 7.19 for the smooth rectangular configuration, representing a 32% enhancement. Similarly, the wavy trapezoidal channel with a top width of 0.18 mm achieves a maximum Nusselt number of 9.25, compared to 7.19 for its smooth equivalent, indicating a 29% improvement. Additionally, the Nu/Nu₀ versus Re plots reveal a consistent trend of increased heat transfer due to wall waviness across all geometries, with negligible influence from cross-sectional shape when hydraulic diameter is kept constant. The study demonstrates that incorporating wavy structures into microchannel designs significantly improves thermal performance with minimal increases in pressure drop, and that the effect is driven more by wall geometry than by cross-sectional shape. These findings provide valuable insights for the development of compact and efficient microchannel heat sinks for electronic cooling applications.

Keywords


Microchannel Heat Sink (MCHS); wavy microchannels; heat transfer enhancement; Reynolds number; Nusselt number; friction factor

Full Text:

PDF

References


Y. Sui, C. J. Teo, P. S. Lee, Y. T. Chew, and C. Shu, “Fluid flow and heat transfer in wavy microchannels,” Int J Heat Mass Transf, vol. 53, no. 13–14, pp. 2760–2772, Jun. 2010, doi: 10.1016/j.ijheatmasstransfer.2010.02.022.

IEEE IRDS, “International roadmap for devices and systems: 2021,” 2021. Accessed: Jan. 01, 2025. [Online]. Available: https://irds.ieee.org/images/files/pdf/2021/2021IRDS_ES.pdf

A. Datta, D. Debbarma, N. Biswas, D. Sanyal, and A. K. Das, “The role of flow structures on the thermal performance of microchannels with wall features,” J Therm Sci Eng Appl, vol. 13, no. 2, Apr. 2021, doi: 10.1115/1.4047709.

D. B. Tuckerman and R. F. W. Pease, “High-performance heat sinking for VLSI,” IEEE Electron Device Letters, vol. 2, no. 5, pp. 126–129, May 1981, doi: 10.1109/EDL.1981.25367.

W. Qu and I. Mudawar, “Experimental and numerical study of pressure drop and heat transfer in a single-phase micro-channel heat sink,” Int J Heat Mass Transf, vol. 45, no. 12, pp. 2549–2565, Jun. 2002, doi: 10.1016/S0017-9310(01)00337-4.

H. Y. Wu and P. Cheng, “An experimental study of convective heat transfer in silicon microchannels with different surface conditions,” Int J Heat Mass Transf, vol. 46, no. 14, pp. 2547–2556, Jul. 2003, doi: 10.1016/S0017-9310(03)00035-8.

K. C. Toh, X. Y. Chen, and J. C. Chai, “Numerical computation of fluid flow and heat transfer in microchannels,” Int J Heat Mass Transf, vol. 45, no. 26, pp. 5133–5141, Dec. 2002, doi: 10.1016/S0017-9310(02)00223-5.

G. Gamrat, M. Favre-Marinet, and D. Asendrych, “Conduction and entrance effects on laminar liquid flow and heat transfer in rectangular microchannels,” Int J Heat Mass Transf, vol. 48, no. 14, pp. 2943–2954, Jul. 2005, doi: 10.1016/j.ijheatmasstransfer.2004.10.006.

M. K. Kang, J. H. Shin, H.-H. Lee, and K. Chun, “Analysis of laminar convective heat transfer in micro heat exchanger for stacked multi-chip module,” Microsystem Technologies, vol. 11, no. 11, pp. 1176–1186, Oct. 2005, doi: 10.1007/s00542-005-0590-9.

P.-S. Lee, S. V. Garimella, and D. Liu, “Investigation of heat transfer in rectangular microchannels,” Int J Heat Mass Transf, vol. 48, no. 9, pp. 1688–1704, Apr. 2005, doi: 10.1016/j.ijheatmasstransfer.2004.11.019.

V. K. Pandey, V. Choudhary, C. Ranganayakulu, and A. A. M., “Thermal hydraulic performance and characteristics of a microchannel heat ex-changer: Experimental and numerical investigations,” ASME Journal of Heat and Mass Transfer, vol. 147, no. 2, Feb. 2025, doi: 10.1115/1.4067012.

M. N. Akram, K. Mohiuddin, M. A. S. Akash, F. Ibeh, and M. S. Kibria, “Numerical investigation on enhanced thermal performance of rectangular microchannels with triangular ribs,” Archives of Advanced Engineering Science, pp. 1–11, Sep. 2024, doi: 10.47852/bonviewAAES42023989.

T. Yu, X. Guo, and Y. Tang, “Numerical investigations of heat transfer augmentation in a microchannel heat sink with different shaped periodic reentrant cavities on channel sidewalls,” Can J Phys, vol. 102, no. 11, pp. 590–603, Nov. 2024, doi: 10.1139/cjp-2023-0275.

D. K. Raj, A. Datta, and N. K. Soni, “Design of the microchannels heat sink to augment the thermal performance using different type of cavity with or without wavy channel,” Heat Transfer Engineering, vol. 46, no. 4–5, pp. 432–449, Mar. 2025, doi: 10.1080/01457632.2024.2317605.

Q. Wang, J. Tao, Z. Cui, T. Zhang, and G. Chen, “Passive enhanced heat transfer, hotspot management and temperature uniformity enhance-ment of electronic devices by micro heat sinks: A review,” Int J Heat Fluid Flow, vol. 107, p. 109368, Jul. 2024, doi: 10.1016/j.ijheatfluidflow.2024.109368.

M. A. Wazir, K. Akhtar, U. Ghani, M. Wajib, S. Shaukat, and H. Ali, “Thermal enhancement of microchannel heat sink using pin-fin configura-tions and geometric optimization,” Engineering Research Express, vol. 6, no. 1, p. 015526, Mar. 2024, doi: 10.1088/2631-8695/ad3400.

S. Ahmed Memon, S. Akhtar, T. Ahmad Cheema, and C. Woo Park, “Enhancing heat transfer in microchannels: A systematic evaluation of crescent-like fin and wall geometries with secondary flow,” Appl Therm Eng, vol. 239, p. 122099, Feb. 2024, doi: 10.1016/j.applthermaleng.2023.122099.

Yew Wai Loon, Nor azwadi Che Sidik, and Yutaka Asako, “Numerical analysis of fluid flow and heat transfer characteristics of novel micro-channel heat sink,” Journal of Advanced Research in Numerical Heat Transfer, vol. 15, no. 1, pp. 1–23, Jan. 2024, doi: 10.37934/arnht.15.1.123.

W. Qu and I. Mudawar, “Experimental and numerical study of pressure drop and heat transfer in a single-phase micro-channel heat sink,” Int J Heat Mass Transf, vol. 45, no. 12, pp. 2549–2565, Jun. 2002, doi: 10.1016/S0017-9310(01)00337-4.

G. Xia, Y. Zhai, and Z. Cui, “Numerical investigation of thermal enhancement in a micro heat sink with fan-shaped reentrant cavities and in-ternal ribs,” Appl Therm Eng, vol. 58, no. 1–2, pp. 52–60, Sep. 2013, doi: 10.1016/j.applthermaleng.2013.04.005.

I. A. Ghani, N. Kamaruzaman, and N. A. C. Sidik, “Heat transfer augmentation in a microchannel heat sink with sinusoidal cavities and rec-tangular ribs,” Int J Heat Mass Transf, vol. 108, pp. 1969–1981, May 2017, doi: 10.1016/j.ijheatmasstransfer.2017.01.046.

Y. F. Li, G. D. Xia, D. D. Ma, Y. T. Jia, and J. Wang, “Characteristics of laminar flow and heat transfer in microchannel heat sink with triangular cavities and rectangular ribs,” Int J Heat Mass Transf, vol. 98, pp. 17–28, Jul. 2016, doi: 10.1016/j.ijheatmasstransfer.2016.03.022.

G. Xia, L. Chai, H. Wang, M. Zhou, and Z. Cui, “Optimum thermal design of microchannel heat sink with triangular reentrant cavities,” Appl Therm Eng, vol. 31, no. 6–7, pp. 1208–1219, May 2011, doi: 10.1016/j.applthermaleng.2010.12.022.

G. Xia, L. Chai, M. Zhou, and H. Wang, “Effects of structural parameters on fluid flow and heat transfer in a microchannel with aligned fan-shaped reentrant cavities,” International Journal of Thermal Sciences, vol. 50, no. 3, pp. 411–419, Mar. 2011, doi: 10.1016/j.ijthermalsci.2010.08.009.

C. B. Rocha, N. C. Constantinou, and S. G. L. Smith, "The Nusselt numbers of horizontal convection," J. Fluid Mech., vol. 894, p. A24, 2020, doi: 10.1017/jfm.2020.269.

S. Saito, S. Baba, K. Kinoshita, and N. Takada, “Thermal-hydraulic performance of additively manufactured AlSi10Mg crossflow minichannel heat exchangers,” SSRN, 2024, doi: 10.2139/ssrn.5039654.




DOI: http://dx.doi.org/10.22441/ijimeam.v7i2.31555

Refbacks

  • There are currently no refbacks.


Copyright (c) 2025 Soumik Kumar Hazra

Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

INDEXED IN

 

Publisher Address:
Universitas Mercu Buana
Program Studi S2 Teknik Mesin
Jl. Meruya Selatan No. 1, Kembangan, Jakarta 11650, Indonesia
Phone/Fax. (+6221) 5871335
Email [email protected]
Homepage mercubuana.ac.id/magister-teknik-mesin

Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.