Review of Natural Fiber Reinforced Epoxy Resin Composite Materials for Automotive Component Applications
DOI:
https://doi.org/10.22441/jtm.v15i01.36798Keywords:
Composite, Epoxy Resin, Natural Fiber, Bio-Composite, Sustainable Automotive.Abstract
Epoxy resin is a thermosetting polymer widely used in composite materials due to its high mechanical strength, excellent chemical resistance, and strong adhesion. In composite structures, epoxy acts as a matrix that binds and protects the reinforcing fibers while transferring loads between components. The reinforcing fibers may be synthetic (e.g., fiberglass, carbon) known for their high tensile strength, or natural fibers (e.g., kenaf, ramie), which offer advantages in sustainability and low weight. With the growing demand for lightweight, efficient, and environmentally friendly automotive materials, epoxy-based composites show significant potential for use in body panels, interior parts, and structural vehicle components. However, challenges remain, such as poor interfacial bonding between epoxy and natural fibers, thermal degradation, and relatively high production costs. This study aims to systematically review current research trends, applications, and research gaps in the development of epoxy resin composites for automotive components, particularly those reinforced with natural fibers. The method used is a Scoping Review based on the PRISMA-ScR framework, covering 50 scientific articles published between 2015 and 2025. The results indicate that kenaf, ramie, and jute fibers have strong potential as sustainable reinforcements, although improvements in interfacial compatibility and processing technology are still critical. The study implies the importance of advancing bio-based epoxy resins, hybrid manufacturing techniques, and the utilization of local natural fibers as part of a sustainable automotive strategyDownloads
References
Z. Muhyidin, “Pengaruh Cangkang Telur Dan Bambu Betung Pada Matriks Epoksi Dan Polyvinyl Acetate (PVAc) Terhadap Sifat Fisik Dan Mekanik Papan Komposit,” pp. 1–99, 2023.
A. W. Gunandar, “Analisis Kekuatan Tarik Dan Impak Bahan Komposit Hibrid Berpenguat Serbuk Kayu Akasia Dan Tandan Kosong Kelapa Sawit,” J. Tek. Mesin, vol. 1, pp. 1–68, 2021, [Online]. Available: http://repository.uir.ac.id/id/eprint/8977
F. F. F. Jalu Nur Septiyanto , Abdul Azis, Naufal Syafiqri and R. Y. Parapat, “Potensi Nanokomposit Dalam Mengoptimalkan Desain Bodi Kendaraan Modern,” Scientica, vol. 3, pp. 169–188, 2025.
R. Hariadi, “Analisis Kekuatan Lentur Bahan Komposit Dari Campuran Serat Pelepah Pinang (Areca Catechu) Dengan Resin Epoxy,” SKripsi Fak. Tek. Univ. Islam Riau, pp. 1–66, 2022.
M. Hilman Hafiduddin, “PENGARUH SILICONE RUBBER TERHADAP SIFAT TARIK DAN KEMAMPUAN INSULASI TERMAL KOMPOSIT EPOXY RESIN BERPENGUAT SERAT TKKS (Tandan Kosong Kelapa Sawit) (Skripsi) Oleh,” 2023.
A. Siregar, “Pemanfaatan Serat Alami (Sabut Kelapa) Sebagai Alternatif Bahan Komposit Pada Spakbor Depan Motor,” pp. 1–51, 2021, [Online]. Available: http://repository.uir.ac.id/id/eprint/8998
M. Fitri, S. Mahzan, D. M. Zago, S. Zakaria, and D. Feriyanto, “Optimization of the second phase morphology and content effect to impact resistance of epoxy resin composite,” BIO Web Conf., vol. 159, 2025, doi: 10.1051/bioconf/202515904006.
H. Pranoto and M. Fitri, “The Effect of Alkali Treatment to Mechanical Properties of Resin Composite Reinforced with Coir Coconut Fiber,” J. Mech. Eng., vol. 19, no. 2, pp. 65–78, 2022, doi: 10.24191/jmeche.v19i2.19765.
M. Fitri, S. Zakaria, D. Feriyanto, and G. Villany Golwa, “Full Factorial and Taguchi Design for the Impact Strength of Oil Palm Fiber Reinforced Composite : A Comparative Study,” Res Mil., vol. 12, no. 5, pp. 1226–1238, 2022, [Online]. Available: https://resmilitaris.net/menu-script/index.php/resmilitaris/article/view/2438/2013
M. Fitri, S. Mahzan, I. Hidayat, and N. Nurato, “the Effect of Coconut Coir Fiber Powder Content and Hardener Weight Fractions on Mechanical Properties of an Epr-174 Epoxy Resin Composite,” Sinergi, vol. 25, no. 3, p. 361, 2021, doi: 10.22441/sinergi.2021.3.013.
I. Risyuma and M. Fitri, “Analysis of Oil Absorption and Friction Coefficient of Bamboo Powder, Coconut Powder, Glass Powder, and Copper Powder Composites for Clutch Pads,” Int. J. Innov. Mech. Eng. Adv. Mater., vol. 4, no. 2, p. 58, 2023, doi: 10.22441/ijimeam.v4i2.18235.
M. Fitri and S. Mahzan, “Influence of coupling agent and fibre treatment to mechanical properties of oil palm fibre reinforced polymer matrix composite,” J. Mech. Eng., vol. 5, no. Specialissue4, pp. 223–232, 2018.
M. Fitri and S. Mahzan, “The effect of fibre content, fibre size and alkali treatment to Charpy impact resistance of Oil Palm fibre reinforced composite material,” IOP Conf. Ser. Mater. Sci. Eng., vol. 160, no. 1, 2016, doi: 10.1088/1757-899X/160/1/012030.
M. Fitri and S. Mahzan, “The Regression Models of Impact Strength of Coir Coconut Fiber Reinforced Resin Matrix Composite Materials,” Int. J. Adv. Technol. Mech. Mechatronics Mater., vol. 1, no. 1, pp. 32–38, 2020, doi: 10.37869/ijatec.v1i1.12.
M. Fitri, S. Mahzan, and F. Anggara, “The Mechanical Properties Requirement for Polymer Composite Automotive Parts - A Review,” Int. J. Adv. Technol. Mech. Mechatronics Mater., vol. 1, no. 3, pp. 125–133, 2021, doi: 10.37869/ijatec.v1i3.38.
M. E. P. Rizki Fahmi Afifi, Dini Cahyandari, “Pengaruh Penambahan Serat Daun Nanas Terhadap Konduktivitas Termal pada Material Komposit Bermatriks Polyurethane,” pp. 869–882.
A. Rosyid, “Analisa Kekuatan Tarik Dan Bending Komposit Resin Polyester Yang Diperkuat Serat Rami Tenun Dengan Orientasi Arah Sudut 0° Dan 45° Sebagai Alternatif Bumper Mobil,” Skripsi Tek. Mesin Univ. Sultan Ageng Tirtayasa, 2022, [Online]. Available: https://eprints.untirta.ac.id/id/eprint/27281
E. Y. D. Syaputra, “Karakterisasi Komposit Resin Epoksi Berpenguat Serat Ampas Tebu untuk Aplikasi Kampas Rem Bebas Asbestos,” 2019.
F. R. Damanik and M. Fitri, “Design Optimization of Composite Resin Pelton Turbine Bucket Using Solidworks,” vol. 12, 2022.
M. Fitri, “Pengaruh Prosentase Serat Kelapa Sawit Terhadap Umur Fatik Beban Aksial Komposit Matriks Resin,” Rotasi, vol. 21, no. 4, p. 215, 2019, doi: 10.14710/rotasi.21.4.215-223.
I. M. Asyrofi, W. T. Putra, and Y. Winardi, “Pengaruh Campuran Plastik Waste LDPE Dan PET Bermatrik Resin Polyester terhadap Kekuatan Tarik dan Struktur Mikro,” TEKNOSAINS J. Sains, Teknol. dan Inform., vol. 10, no. 1, pp. 51–58, 2023.
I. Tanjung, “Analisis Morfologi Serat Dan Kekuatan Impak Bahan Komposit Berpenguat Serat Pinang (Areca Catechu) Yang Telah Dilakukan Perbaikan Sifat Fisik,” VOCATECH Vocat. Educ. Technol. J., vol. 4, no. 1, pp. 1–7, 2022, doi: 10.38038/vocatech.v4i1.108.
J. T. Mesin, F. T. Industri, and U. I. Indonesia, “PEMBUATAN PRODUK KOMPOSIT HAND GUARD SEPEDA MOTOR TOURING BERPENGUAT WOVEN CARBON FIBER MENGGUNAKAN METODE COMPRESSION MOLDING,” 2025.
E. Lastri, “Pengaruh Perlakuan Alkali Terhadap Sifat Mekanik Pada Komposit Berpenguat Serat Alam : Penelitian Kepustakaan,” Jur. Tek. Metal. Fak. Tek. Univ. Sultan Ageng Tirtayasa, 2023.
M. W. Ubaidillah, D. A. Rokhmah Wati, M. M. Rosadi, and M. A. Irfa’I, “Pengaruh Fraksi Volume Serat Kelapa Bermatriks Epoxy Terhadap Kekuatan Tarik Komposit,” J. MOTION ( Manufaktur, Otomasi, Otomotif, dan Energi Terbarukan), vol. 2, no. 02, pp. 24–29, 2024, doi: 10.33752/motion.v2i02.6256.
S. Marpaung, “SIMULASI NUMERIK DAN ANALISIS KEKUATAN TARIK BELAH KOMPOSIT LAMINAT JUTE / EPOKSI DENGAN ANSYS WORKBENCH 2022,” 2025.
A. D. Akbar, “Studi Laju Keausan Dan Stabilitas Dimensi Kampas Rem Organik Yang Menggunakan Kombinasi Partikel Cangkang Telur Dan Bambu,” vol. 1, 2023, [Online]. Available: https://eprints.untirta.ac.id/id/eprint/35163%0Ahttps://eprints.untirta.ac.id/35163/7/Adam Dzulfikhar Akbar_3331170061_Fulltext.pdf
H. P. Kinanty Z, H. Ardhyananta, and A. Rasyida, “Tinjauan Pengaruh Jenis Material Sizing Poliuretan, Silane Coupling Agent, dan Poliimida pada Serat Karbon terhadap Morfologi dan Sifat Mekanik Komposit Epoksi/Serat Karbon untuk Aplikasi Bilah Turbin Angin,” J. Tek. ITS, vol. 9, no. 2, 2021, doi: 10.12962/j23373539.v9i2.53873.
E. Fakhruddin, M. Asad Abdurrahman, and S. MEngPM, Pembimbing Pendamping Dekan Fakultas Teknik Universitas Hasanuddin Ketua Program Studi S2 Teknik Sipil. 2024.
J. R. Material and M. Energi, “FT-UMSU FT-UMSU,” vol. 7, no. 1, pp. 168–175, 2024.
E. Matei et al., “Natural Polymers and Their Nanocomposites Used for Environmental Applications,” Nanomaterials, vol. 12, no. 10, 2022, doi: 10.3390/nano12101707.
P. A. Pramana, M. Fitri, A. Hamid, and D. Romahadi, “Effect of Water Hyacinth Fiber Length and Content on the Torsional Strength of Epoxy Resin Composites,” vol. 6, no. 3, pp. 144–151, 2024, doi: 10.22441/ijimeam.v6i3.19701.
M. Fitri, T. Susilo, D. Feriyanto, and D. M. Zago, “Effect Of Morphology And Percentage Of Second Phase Content Of Coconut Coir On The Impact Strength Of Epoxy Resin Composites,” Volatiles Essent. Oils, vol. 8, no. 6, pp. 3880–3894, 2021.
R. Nurgiansyah and M. Fitri, “Pengaruh Kandungan Serbuk Sekam Padi , Serbuk Kulit Kacang Tanah , dan Serat Ijuk Terhadap Kekuatan Impak dan Mikrostruktur Komposit Matriks Resin,” vol. 20, no. 1, pp. 56–64, 2025.
S. N. Kane, A. Mishra, and A. K. Dutta, “Preface: International Conference on Recent Trends in Physics (ICRTP 2016),” J. Phys. Conf. Ser., vol. 755, no. 1, 2016, doi: 10.1088/1742-6596/755/1/011001.
M. A. Ihsan, “Studi Pengaruh Komposisi Filler Batu Alam dan Limbah Melamin Terhadap Sifat Mekanik dan Sifat Fisis Material Komposit Epoksi/Melamin/Batu Alam Untuk Aplikasi Tile,” Dep. Tek. Mater. Fak. Teknol. Ind. ITS Surabaya, pp. 1–103, 2018, [Online]. Available: https://repository.its.ac.id/53042/
R. Damaru, A. Novaringga, Darmansyah, and S. Br. Ginting, “Indonesian Journal of Chemical Science Resin Composite Synthesis Reinforced with Banana Tree Fiber with Carboxylic Silica (SiO2-COOH) Addition as a Nanofiller,” J. Chem. Sci, vol. 10, no. 1, 2021, [Online]. Available: http://journal.unnes.ac.id/sju/index.php/ijcs
F. Teknik and U. P. Tegal, “Analisa Kekuatan Mekanis Pada Material,” 2019.
L. L. Gaol, “Studi Sifat Mekanikal Biokomposit Poli Asam Laktat Partikel Serat Pisang dengan Penambahan Bahan Penyerasi (Compatibilizing Agent),” 2023, [Online]. Available: https://repositori.uma.ac.id/handle/123456789/21754%0Ahttps://repositori.uma.ac.id/jspui/bitstream/123456789/21754/1/188130122 - Leonardo Lumban Gaol - Fulltext.pdf
J. T. Mesin, F. T. Industri, and U. I. Indonesia, “KEKUATAN BENDING RANGKA PRODUK KOMPOSIT MENGGUNAKAN MATERIAL KOMPOSIT SANDWICH DENGAN INTI POLIMER PRODUK 3D PRINTING MENGGUNAKAN MATERIAL KOMPOSIT SANDWICH DENGAN INTI POLIMER PRODUK 3D PRINTING,” 2024.
Rusnoto and Soebyakto, “Studi Penambahan Serbuk Alumina pada Kerapatan/Densitas Komposit Matrik Epoksi,” pp. 1–32, 2020, [Online]. Available: https://repository.upstegal.ac.id/2824/1/SCAN LAPORAN PENELITIAN GENAP 19-20 DENSITAS KOMPOSIT RUSNOTO.pdf
S. Green et al., “Challenges in Recycling of Multi-Material Composites,” pp. 9–16, 2015.
R. R. Deri, “Integrasi Limbah Kayu dan Resin Menjadi Jam dengan Pendekatan Sustainable Product Design,” vol. 1, no. 3, pp. 531–537, 2025.
M. K. Huda and I. Widiastuti, “Natural Fiber Reinforced Polymer in Automotive Application: A Systematic Literature Review,” IOP Conf. Ser. Earth Environ. Sci., vol. 1808, no. 1, 2021, doi: 10.1088/1742-6596/1808/1/012015.
U. Fajar, “PEMANFAATAN CAMPURAN AMPAS TEBU DAN ALUMINIUM SEBAGAI MATERIAL ALTERNATIF KAMPAS REM CAKRAM SEPEDA MOTOR NON-ASBESTOS MATERIAL ALTERNATIF KAMPAS REM CAKRAM SEPEDA MOTOR NON-ASBESTOS,” 2022.
M. E. Seminar, H. Pranoto, and M. Fitri, “APLIKASINYA PADA PERKERETAAPIAN,” pp. 10–17, 2024.
M. Afif, R. Nurmeyliandari, and D. S. Devi, “KARAKTERISTIK KUAT TARIK BETON POLIMER DENGAN VARIASI SERAT KAWAT BENDRAT,” vol. 9, pp. 107–116, 2024.
H. Sukanto, B. Kusharjanta, and M. Kaavessina, “Improving Solvolysis Rate Via Under Glass-Transition Temperatures Quenching Followed by Roll Bending of Carbon Fiber Reinforced Polymer Composite,” vol. 45, no. 3, pp. 279–288, 2024, doi: 10.14710/teknik.v45i3.59296.
B. Karacor and M. Özcanlı, “A Short Review: The Use and Application of Matrix Resins Formed with Some Plant-Based Oils in Bio-Composite Materials,” Düzce Üniversitesi Bilim ve Teknol. Derg., vol. 12, no. 3, pp. 1315–1333, 2024, doi: 10.29130/dubited.1265905.
I. Y. Enis and H. Sezgi̇n, “Full factorial experimental design for water absorption and wettability of jute fabric reinforced acrylated epoxidized soybean oil/epoxy biocomposites,” Tekst. ve Muhendis, vol. 28, no. 123, pp. 163–170, 2021, doi: 10.7216/1300759920212812301.
E. Widodo and I. Dwiyoga, “ANALISIS PENGARUH ALKALISASI NaOH TERHADAP SERAT NANAS SEBAGAI PENGUATAN BIO KOMPOSIT,” Otopro, vol. 18, no. 1, pp. 1–6, 2022, doi: 10.26740/otopro.v18n1.p1-6.
A. Saputra, P. Satwikanitya, M. Wahyu, and M. F. Agustian, “Studi Perbandingan Sifat Mekanis Vulkanisat Karet Menggunakan Plasticizer Minyak Jelantah Epoksi Dan Komersil,” J. Teknol. Ramah Lingkung., vol. 7, pp. 138–151, 2023.
B. Fish, STUDI PEMBUATAN KOMPOSIT DENGAN METODE VACUUM ASSISTED RESIN TRANSFER MOULDING DAN REVIEW PENGUJIAN SIFAT MEKANI, vol. 2507, no. February. 2020.
Downloads
Additional Files
Published
How to Cite
Issue
Section
License
The copyright to this article is transferred to Universitas Mercu Buana (UMB) if and when the article is accepted for publication. The undersigned hereby transfers any and all rights in and to the paper including without limitation all copyrights to UMB. The undersigned hereby represents and warrants that the paper is original and that he/she is the author of the paper, except for material that is clearly identified as to its original source, with permission notices from the copyright owners where required. The undersigned represents that he/she has the power and authority to make and execute this assignment.
We declare that:
1. This paper has not been published in the same form elsewhere.
2. It will not be submitted anywhere else for publication prior to acceptance/rejection by this Journal.
3. A copyright permission is obtained for materials published elsewhere and which require this permission for reproduction.
Furthermore, I/We hereby transfer the unlimited rights of publication of the above mentioned paper in whole to UMB. The copyright transfer covers the exclusive right to reproduce and distribute the article, including reprints, translations, photographic reproductions, microform, electronic form (offline, online) or any other reproductions of similar nature.
The corresponding author signs for and accepts responsibility for releasing this material on behalf of any and all co-authors. This agreement is to be signed by at least one of the authors who have obtained the assent of the co-author(s) where applicable. After submission of this agreement signed by the corresponding author, changes of authorship or in the order of the authors listed will not be accepted.
Retained Rights/Terms and Conditions
1. Authors retain all proprietary rights in any process, procedure, or article of manufacture described in the Work.
2. Authors may reproduce or authorize others to reproduce the Work or derivative works for the authors personal use or for company use, provided that the source and the UMB copyright notice are indicated, the copies are not used in any way that implies UMB endorsement of a product or service of any employer, and the copies themselves are not offered for sale.
3. Although authors are permitted to re-use all or portions of the Work in other works, this does not include granting third-party requests for reprinting, republishing, or other types of re-use.
This work is also licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
