EFFECT OF WELDING HEAT INPUT ON THE CORROSION RATE OF CARBON STEEL MMA WELDING
DOI:
https://doi.org/10.22441/ijimeam.v3i1.11667Kata Kunci:
welding current, corrosion rate, MMA welding, low carbon steel.Abstrak
Abstract
Steel is one of materials which often used on steel construction, bridge construction, and high rise building construction. Construction using welding joint is expected able to withstand construction loads for a long time. After a while weldment will be exposed to corrosion that will be construction failure in turn. One of the most important parameter in welding is heat input, however it hasn’t obtain correlation between heat input and corrosion rate on MMA (Manual Metal Arch) weldment on mild steel. This paper aims to obtain correlation between heat input and corrosion rate of low carbon steel with MMA welding. The result was show that corrosion rate tend to decrease with adding of duration, where higher corrosion rate at heat input 0,8108 kJ/mm was 68,68 gm/m2 hr at duration 5 hour.
Unduhan
Referensi
Umiati, S. Ketahanan Material Baja Sebagai Struktur Bangunan Terhad[1] Umiati, S. Ketahanan Material Baja Sebagai Struktur Bangunan Terhadap Kebakaran. Jurnal, 29 2008).
Saha, M. K., Hazra, R., Mondal, A. and Das, S. Effect of heat input on geometry of austenitic stainless steel weld bead on low carbon steel. Journal of The Institution of Engineers (India): Series C, 100, 4 2019), 607-615.
Lu, Y., Jing, H., Han, Y. and Xu, L. Effect of welding heat input on the corrosion resistance of carbon steel weld metal. Journal of Materials Engineering and Performance, 25, 2 2016), 565-576.
Saha, M. K., Mondal, J., Mondal, A. and Das, S. Influence of Heat input on Corrosion Resistance of Duplex Stainless Steel Cladding Using Flux Cored Arc Welding on Low Alloy Steel Flats. Indian Welding Journal, 51, 3 2018).
Paulraj, P. and Garg, R. Effect of welding parameters on pitting behavior of GTAW of DSS and super DSS weldments. Engineering Science and Technology, an International Journal, 19, 2 2016), 1076-1083.
Frei, J., Alexandrov, B. T. and Rethmeier, M. Low heat input gas metal arc welding for dissimilar metal weld overlays part I: the heat-affected zone. Welding in the World, 60, 3 2016), 459-473.
Shirazi, A. Z. and Mohammadi, Z. A hybrid intelligent model combining ANN and imperialist competitive algorithm for prediction of corrosion rate in 3C steel under seawater environment. Neural Computing and Applications, 28, 11 2017), 3455-3464.
Hassan, K. S., Alamran, Y. T. and Abdulaziz, H. M. INVESTIGATION CORROSION BEHAVIOUR OF DUCTILE CAST IRON WELD JOINT IN SEA WATER. Iraqi journal of mechanical and material engineering, 18, 1 2018), 1-14.
Otieno, M., Beushausen, H. and Alexander, M. Chloride-induced corrosion of steel in cracked concrete—Part II: Corrosion rate prediction models. Cement and concrete Research, 792016), 386-394.
Vanaei, H., Eslami, A. and Egbewande, A. A review on pipeline corrosion, in-line inspection (ILI), and corrosion growth rate models. International Journal of Pressure Vessels and Piping, 1492017), 43-54.
Ghorbani, S., Ghasemi, R., Ebrahimi-Kahrizsangi, R. and Hojjati-Najafabadi, A. Effect of post weld heat treatment (PWHT) on the microstructure, mechanical properties, and corrosion resistance of dissimilar stainless steels. Materials Science and Engineering: A, 6882017), 470-479.
Mohan, D. G., Gopi, S. and Rajasekar, V. Effect of induction heated friction stir welding on corrosive behaviour, mechanical properties and microstructure of AISI 410 stainless steel2018).
Xu, L., Jing, H. and Han, Y. Effect of welding on the corrosion behavior of X65/Inconel 625 in simulated solution. Welding in the World, 62, 2 2018), 363-375.
Anonym KOBELCO Welding Today. City, 2001.
ASTM, G. 48-03 (Reapproved 2009),". Standard Test Methods for Pitting and Crevice Corrosion Resistance of Stainless Steels and Related Alloys by Use of Ferric Chloride Solution.
Oktoriansyah, R., Hartono, B. and Sutoyo, E. Analisa Laju Korosi Akibat Pengelasan Duplex UNS32205 Dengan 2 Metode Pengelasan yang Berbeda Pada Media FeCl3. AME (Aplikasi Mekanika dan Energi): Jurnal Ilmiah Teknik Mesin, 3, 2 2017), 77.
Unduhan
Diterbitkan
Cara Mengutip
Terbitan
Bagian
Lisensi
Authors who publish in IJIMEAM retain the following rights:- Author retains the copyright and grants the journal the right of first publication of the work simultaneously licensed under the Creative Commons Attribution-ShareAlike 4.0 License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
- Author is able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book) with the acknowledgment of its initial publication in this journal.
- Author is permitted and encouraged to post his/her work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of the published work (See What is Open Access).
Read more about the Creative Commons Attribution-ShareAlike 4.0 Licence here: https://creativecommons.org/licenses/by-sa/4.0/.
