Optimization of plastic injection molding process parameters for cowl B (L/R) sink mark defects by using Taguchi methods and ANOVA
DOI:
https://doi.org/10.22441/oe.2023.v15.i1.069Kata Kunci:
ANOVA, injection parameters, sink mark, Taguchi methodAbstrak
The plastic injection molding process on Cowl B (L/R) products that have been carried out has sink mark defects. The defects that arise occur because the composition of injection molding parameter values is not optimal in the variables of melt temperature, mold temperature, packing time, packing pressure, and cooling time. The purpose of this study is to find the optimal composition of parameter values for each variable, to minimize sink mark defects in the product. The analysis process begins with the preparation of an orthogonal array matrix to determine the design parameters to be simulated on Autodesk mold flow. These results are evaluated with a signal-to-noise ratio to determine the effect of each parameter value composition on the results of the analysis process. The Analysis of Variance (ANOVA) method is used to estimate the contribution of each independent variable to all response measurements (the dependent variable). The optimization results for sink mark defects in the sink mark index value of 1.4494%, volumetric shrinkage of 0.5053%, and sink mark estimate of 0.0608 mm are found in the composition of the parameter values of melt temperature 200°C, mold temperature 80°C, packing time 30 seconds, packing pressure 80 MPa and a cooling time of 13,365 seconds. This data is used as a reference in determining parameters before production is carried out on plastic injection molding machines so that the time and cost of testing the injection molding process are optimal.Unduhan
Referensi
Bhatagalikar, S., & Adewar, MSS (2020). Design and Process Optimization of Masks: Numerical
Modeling with Experimental Validation. International Research Journal of Modernization in
Engineering (Ijmets), 02 (08), 300–309. www.irjmets.com
Budiyantoro, C. (2016). Optimization of Sink Mark Index on Products Plastic with Variations
Thickness Extreme Use Moldflow Simulation (Sink Mark Index Optimization of Plastic
Products with Extreme Thickness Variation using Moldflow Simulation). Universe Teknika,
(2), 134-141.
Hadisaputra, N. S., & Hasibuan, S. (2022). Analysis of OEE improvements in Blow Molding
Machines in the Plastic Packaging Manufacturing Industry using Six Big Losses and FMEA
methods. Proceedings of the International Conference on Industrial Engineering and
Operations Management, Nsukka, Nigeria, 5 - 7 April, 2022
Hartono, Moh., Pratikto, Santoso, PB, & Sugiono. (2020). Optimization on the Injection Molding
Propypopylene Parameters Using Central Composite Design for Minimizing Defects. Journal
of Southwest Jiaotong University, 55 (2), 1–11. https://doi.org/10.35741/issn.0258-
55.2.42
Inui, M., Onishi, S., & Umezu, N. (2018). Visualization of potential sink marks using thickness
analysis of finely tessellated solid models. Journal of Computational Design and
Engineering, 5 (4), 409–418. https://doi.org/10.1016/j.jcde.2018.02.003
Ja'afar, R., Arep , H., Mohamad, E., Abd Razak, J., Arfauz A Rahman, M., & Yuniarti , R. (2020).
Analysis on Volumetric Shrinkage of Plastic Food Container Made from an Injection Molding
Process. Journal of Engineering and Management in Industrial Systems, 8 (2), 22–31.
https://doi.org/10.21776/ub.jemis.2020.008.02.3
Operations Excellence: Journal of Applied Industrial Engineering 2023, 15(1), 21-28
Kerkstra, R., & Brammer, S. (2018). Injection Molding Advanced Troubleshooting Guide. In
Injection Molding Advanced Troubleshooting Guide.
https://doi.org/10.3139/9781569906460.fm
Kumar, SPA (2019). Minimization of Sink Mark Defects in Injection Molding Process Optimization
of a Composite Drive Shaft Used in Automobiles. International Journal of Innovative
Technology and Exploring Engineering, 8 (12S2), 292–294.
https://doi.org/10.35940/ijitee.l1051.10812s219
Li, S., Zhao, G., Dong, G., & Wang, J. (2016). Study on Reducing Sink Mark Depth of a
Microcellular Injection Molded Part with Many Reinforcing Ribs. Journal of Cellular Plastics,
(5), 479–502. https://doi.org/10.1177/0021955X15579244
Lin, F., Duan, J., Lu, Q., & Li, X. (2022). Optimization Of Injection Molding Quality Based on Bp
Neural Network And PSO. Materiali in Tehnologije, 56 (5), 491–497.
https://doi.org/10.17222/mit.2022.516
Lozano, AB, Álvarez, SH, Isaza, CV, & Montealegre -Rubio, W. (2022). Analysis and Advances in
Additive Manufacturing as a New Technology to Make Polymer Injection Molds for WorldClass Production Systems. Polymers, 14 (9), 12–17. https://doi.org/10.3390/polym14091646
Md. Anwarullah, & SP. ArunKumar. (2019). Minimization of Sink Mark Defects in Injection Molding
Process Optimization of a Composite Drive Shaft Used in Automobiles. International Journal
of Innovative Technology and Exploring Engineering, 8 (12S2), 292-294.
https://doi.org/10.35940/ijitee.l1051.10812s219
Moayyedian, M. (2019). Intelligent Optimization of Mold Design and Process Parameters in
Injection Molding. In Springer.
Munankar, AB, Sitap, NA, Tembhurkar, AA, Thakur, MB, & Kanse, SS (2019). Simulation for
optimum gate location in plastic injection molding for spanners. International Research
Journal of Engineering and Technology (IRJET), 06 (04), 1228-1234.
Nippon A&L. (2023). Nippon A & L KRALASTIC TM GA-501 ABS, High impact resistance. Mathweb.
https://www.matweb.com/search/datasheet.aspx?matguid=37a64ac316af4b5493f65614460
ec188
Ogorodnyk, O., & Martinsen, K. (2018). Monitoring and Control for Thermoplastic Injection Molding
A Review. Procedia CIRP, 67, 380–385. https://doi.org/10.1016/j.procir.2017.12.229
Oliaei, E., Heidari, BS, Davachi, SM, Bahrami, M., Davoodi, S., Hejazi, I., & Seyfi, J. (2016).
Warpage and Shrinkage Optimization of Injection-Molded Plastic Spoon Parts for
Biodegradable Polymers Using Taguchi, ANOVA and Artificial Neural Network Methods.
Journal of Materials Science and Technology, 32 (8), 710-720.
https://doi.org/10.1016/j.jmst.2016.05.010
Setya Hutama, A., & Nicolas Axel Reyhan, W. (2022). Minimizing Sink Mark Defects in the Injection
Molding Process of Female GeNose C19 T-Valve Products. Journal of Textiles (JUTE), 5
(2), 69–76. https://jute.ak-tekstilsolo.ac.id/index.php/jurnal/article/view/38/27
Solanki, BS, Singh, H., & Sheorey, T. (2021). Design optimization of feed system for injection
molded polymer gear. Materials Today: Proceedings, 47 (11), 3418–3424.
https://doi.org/10.1016/j.matpr.2021.07.289
Sreedharan, J., & Jeevanantham, AK (2018). Optimization of Injection Molding Process to Minimize
Weld-line and Sink-mark Defects Using Taguchi based Gray Relational Analysis. Materials
Today: Proceedings, 5, 12615-12622.
www.sciencedirect.comwww.materialstoday.com/proceedings2214-7853
Sun, X., Tibbenham, P., Zeng, D., Su, X., Huang, S., & Kang, H. tae . (2019). Procedure
development for predicting the sink mark of injection molded thermoplastics by finite element
method. International Journal of Advanced Manufacturing Technology, 103 (9–12), 4095-
https://doi.org/10.1007/s00170-019-03687-1
Valero, J. R. L. (2020b). Plastics Injection Molding - Scientific Molding, Recommendations, and
Best Practices (Dr. J. Diaz-Luque, Ed.; 1st ed., Vol. 1). Hanser Publications.
https://doi.org/doi.org/10.3139/9781569906903.fm.
Operations Excellence: Journal of Applied Industrial Engineering 2023, 15(1), 21-28
Wibowo, E.A., Sofyan, E., Syahriar, A., Nugroho, AAD, Widiatmoko, F., & Arwidhiatma, PGC
(2021). Optimization of Warpage Defects of Base Pencil Box by Using Backpropagation
Neural Network and Genetic Algorithm. Conference on Management and Engineering in
Industry (CMEI) Optimization, 17-22. https://doi.org/2686-3278
Wibowo, E.A., Sukarnoto, T., & Wibowo, Y.T. (2019). Research of Injection Molding Parameters
with Acrylonitrile Butadiene Styrene Composition Recycled Against Mechanical Properties.
Journal of Physics: Conference Series, 1230 (1), 1-15. https://doi.org/10.1088/1742-
/1230/1/012084
Wibowo, EA, Syahriar, A., & Kaswadi, A. (2020). Analysis and Simulation of Short Shot Defects in
Plastic Injection Molding at Multi Cavities. ACM International Conference Proceeding Series,
-7. https://doi.org/10.1145/3429789.3429837
Zhao, N. Yang, Lian, J. Yuan, Wang, P. Fei, & Xu, Z. Bin. (2022). Recent progress in minimizing
the warpage and shrinkage deformations by the optimization of process parameters in
plastic injection molding: a review. International Journal of Advanced Manufacturing
Technology, 85-101. https://doi.org/10.1007/s00170-022-08859-0
Unduhan
Diterbitkan
Cara Mengutip
Terbitan
Bagian
Lisensi
The copyright to this article is transferred to Universitas Mercu Buana (UMB) if and when the article is accepted for publication. The undersigned hereby transfers any and all rights in and to the paper including without limitation all copyrights to UMB. The undersigned hereby represents and warrants that the paper is original and that he/she is the author of the paper, except for material that is clearly identified as to its original source, with permission notices from the copyright owners where required. The undersigned represents that he/she has the power and authority to make and execute this assignment.
We declare that:
1. This paper has not been published in the same form elsewhere.
2. It will not be submitted anywhere else for publication prior to acceptance/rejection by this Journal.
3. A copyright permission is obtained for materials published elsewhere and which require this permission for reproduction.
Furthermore, I/We hereby transfer the unlimited rights of publication of the above mentioned paper in whole to UMB. The copyright transfer covers the exclusive right to reproduce and distribute the article, including reprints, translations, photographic reproductions, microform, electronic form (offline, online) or any other reproductions of similar nature.
The corresponding author signs for and accepts responsibility for releasing this material on behalf of any and all co-authors. This agreement is to be signed by at least one of the authors who have obtained the assent of the co-author(s) where applicable. After submission of this agreement signed by the corresponding author, changes of authorship or in the order of the authors listed will not be accepted.
Retained Rights/Terms and Conditions
1. Authors retain all proprietary rights in any process, procedure, or article of manufacture described in the Work.
2. Authors may reproduce or authorize others to reproduce the Work or derivative works for the authors personal use or for company use, provided that the source and the UMB copyright notice are indicated, the copies are not used in any way that implies UMB endorsement of a product or service of any employer, and the copies themselves are not offered for sale.
3. Although authors are permitted to re-use all or portions of the Work in other works, this does not include granting third-party requests for reprinting, republishing, or other types of re-use.
