IMPLEMENTATION OF THE FINITE ELEMENT METHOD IN SOLIDWORKS TO OPTIMIZE THE FRONT CAST WHEEL DESIGN FOR MOTORCYCLES

Rizki Nur Afami Kurniawan; Dedik Romahadi; Muhamad Fitri; Md Radwanul Karim

doi:10.22441/ijimeam.v4i3.18794

IMPLEMENTATION OF THE FINITE ELEMENT METHOD IN SOLIDWORKS TO OPTIMIZE THE FRONT CAST WHEEL DESIGN FOR MOTORCYCLES

Penulis

Rizki Nur Afami Kurniawan Universitas Mercu Buana, Indonesia
Dedik Romahadi Universitas Mercu Buana, Indonesia http://orcid.org/0000-0002-9835-5453
Muhamad Fitri Universitas Mercu Buana, Indonesia http://orcid.org/0000-0003-2079-3442
Md Radwanul Karim Beijing Institute of Technology, China

DOI:

https://doi.org/10.22441/ijimeam.v4i3.18794

Kata Kunci:

Cast wheel rims, Finite Element Analysis, Von Mises Stress, Safety Factor

Abstrak

Cast wheel rims often experience damage that causes damage to the lip of the rim, or the spokes rupture if it supports the excessive load. The safety aspect is very important to be considered in the automotive industry because it involves the lives of passengers. Structural optimization of various vehicle components has shown that component weight strongly influences vehicle performance. Based on these problems, this research aims to design a lightweight cast wheel design model that can withstand a load of 535 N. So, it is necessary to make an analysis using a comparison of design models and material variations and static simulations using Solidworks 2018 software. The results sought are von mises, displacement, strain, a factor of safety, and produce a lightweight design. The simulation results on the three models are still safe in holding a load of 535 N because the value of the factor of safety is not less than 1. The results of the design mass with material variations are lighter than the original wheels.

Unduhan

Data unduhan belum tersedia.

Referensi

Sorongan, F. A. (2019). Pengaruh return on assets, return on equity, earning per share terhadap harga saham pada perusahaan otomotif yang terdaftar BEI. JMBI UNSRAT (Jurnal Ilmiah Manajemen Bisnis dan Inovasi Universitas Sam Ratulangi), 6(2), 106–114.

Iskandar, A., Sulaeman, A., Rofiroh, R., & Rizky, P. (2022). analisis performance velg vrossi honda scoopy dengan Finite Element Analysis Method (FEAM) menggunakan Solidworks. Motor Bakar: Jurnal Teknik Mesin, 5(1), 1-8.

Widyantoro, M., Solihin, S., & Rifda, I. R. (2020). Peningkatan efisiensi pada lini proses machining velg motor dengan metode line balancing PT. XYZ Murwan. Jurnal Penelitian dan Aplikasi Sistem & Teknik Industri (PASTI), 14(01), 54-64.

Zuli, M. (2016). Analisis sifat mekanik dan struktur mikro velg sepeda motor spoke wheel dan cast wheel. Barometer, 1(1), 18-20.

Dahlan, A., & Rusiyanto, R. (2021). Pengaruh penambahan unsur aluminium murni pada bahan aluminium scrap terhadap ketangguhan impak dan struktur mikro hasil pengecoran velg motor Honda. Jurnal Dinamika Vokasional Teknik Mesin, 6(1), 58-68.

Trimulya, C. T., Cholis, N., Pradana, S., & Wahyuni, F. (2020). Analisis produk pelek motor tipe cast wheel berbahan paduan alumunium. Bina Tek., 16(2), 79–84.

Santoso, E. T. F., Anwar, C., & Heryana, G. (2020). Analisis kegagalan produk presered concrete girder I akibat deformasi cetakan dengan menggunakan metode elemen hingga. Jurnal Teknologika, 10(2), 27-36.

Warsito, A., Bukit, M., & Johannes, A. Z. (2022). Analisis sifat mekanik modifikasi kemiringan mercu spillway tipe ogee dengan studi kasus bendungan Raknamo menggunakan metode elemen hingga software Elmer. Jurnal Fisika: Fisika Sains dan Aplikasinya, 7(1), 69-74.

Lubis, S. (2019). Analisis pengaruh besar gesekan terhadap tegangan thermal pada sepatu rem mobil ketebalan 8 mm menggunakan perangkat lunak Msc. Nastran V. 9. Jurnal Rekayasa Material, Manufaktur dan Energi, 2(1), 44-53.

Romahadi, D., Ruhyat, N., & Dorion, L. D. (2020). Condensor design analysis with Kays and London surface dimensions. Sinergi, 24(2), 81-86.

Rasyid, M. K. (2018). Analisis bentuk penampang batang engkol menggunakan metode elemen hingga. J. Tek. Mesin ITI, 2(1), 12–15.

Anjasmoro, G., Robbi, N., & Choirotin, I. (2022). Analisis kekuatan pembebanan rangka pada perancangan mesin pencetak pelet menggunakan simulasi Solidworks. J. Sains dan Teknol. Tek. Mesin Unisma, 18(2), 195-201.

Adi, I. N. A., Dantes, K. R., & Nugraha, I. N. P. (2018). Analisis tegangan statik pada rancangan frame mobil listrik Ganesha Sakti (Gaski) menggunakan software Solidworks 2014. Jurnal Pendidikan Teknik Mesin Undiksha, 6(2), 113-120.

Randis, Maulana, N., & Hermansyah, H. (2021). Perancangan dan simulasi struktur rangka overhaul stand untuk penggunaan assembly dan diassembly hydraulic cylinder menggunakan software Solidwork, Jurnal Teknik Mesin, 10(1), 36.

Romahadi, D., Feriyanto, D., Suprihatiningsih, W., & Setiawan, W. N. (2022). Perancangan sistem diagnosis getaran motor menggunakan jaringan saraf tiruan propagasi mundur. Jurnal Rekayasa Mesin, 13(1), 37-46.

Syaefudin, E. A., & Basori, I. (2013). Perancangan desain velg sepeda motor hybrid dan pengujian distribusi beban dengan software Autodesk Inventor. Jurnal Konversi Energi dan Manufaktur, 1(1), 22-31.

Joshi, H., Powar, A., Khuley, S., & Yesane, D. P. (2016). Analysis and topological optimization of motorcycle front wheel. Int. J. Curr. Eng. Technol., 6(6), 265–269.

Yamaha Motor Co. (2022). Yamaha Vixion R spesifikasi.

Syahputri, A., & Karjadidjaja, I. (2022). Hubungan pola aktivitas fisik dengan Indeks Massa Tubuh (IMT) dan lingkar pinggang pengunjung usia dewasa di Puskesmas Kecamatan Kalideres Jakarta Barat. Tarumanagara Medical Journal, 4(1), 1-7.

Unduhan

PDF (English)

Diterbitkan

2023-05-31

Cara Mengutip

Kurniawan RNA, Romahadi D, Fitri M, Karim MR. IMPLEMENTATION OF THE FINITE ELEMENT METHOD IN SOLIDWORKS TO OPTIMIZE THE FRONT CAST WHEEL DESIGN FOR MOTORCYCLES. Int. J. Innov. Mech. Eng. Adv. Mater [Internet]. 31 Mei 2023 [dikutip 3 Juni 2026];4(3):66-73. Tersedia pada: https://publikasi.mercubuana.ac.id/index.php/ijimeam/article/view/18794

Unduh Sitasi

Terbitan

Vol 4 No 3 (2022)

Bagian

Articles

Lisensi

Authors who publish in IJIMEAM retain the following rights:

Author retains the copyright and grants the journal the right of first publication of the work simultaneously licensed under the Creative Commons Attribution-ShareAlike 4.0 License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
Author is able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book) with the acknowledgment of its initial publication in this journal.
Author is permitted and encouraged to post his/her work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of the published work (See What is Open Access).

Read more about the Creative Commons Attribution-ShareAlike 4.0 Licence here: https://creativecommons.org/licenses/by-sa/4.0/.