Optimization of plastic injection molding process parameters for cowl B (L/R) sink mark defects by using Taguchi methods and ANOVA

Eko Ari Wibowo, Muhammad Nur Wahyu Hidayah, Rohmat Setiawan, Yohanes Trijoko Wibowo, Bonaventura Lingga Krisna

Abstract


The plastic injection molding process on Cowl B (L/R) products that have been carried out has sink mark defects. The defects that arise occur because the composition of injection molding parameter values is not optimal in the variables of melt temperature, mold temperature, packing time, packing pressure, and cooling time. The purpose of this study is to find the optimal composition of parameter values for each variable, to minimize sink mark defects in the product. The analysis process begins with the preparation of an orthogonal array matrix to determine the design parameters to be simulated on Autodesk mold flow. These results are evaluated with a signal-to-noise ratio to determine the effect of each parameter value composition on the results of the analysis process. The Analysis of Variance (ANOVA) method is used to estimate the contribution of each independent variable to all response measurements (the dependent variable). The optimization results for sink mark defects in the sink mark index value of 1.4494%, volumetric shrinkage of 0.5053%, and sink mark estimate of 0.0608 mm are found in the composition of the parameter values of melt temperature 200°C, mold temperature 80°C, packing time 30 seconds, packing pressure 80 MPa and a cooling time of 13,365 seconds. This data is used as a reference in determining parameters before production is carried out on plastic injection molding machines so that the time and cost of testing the injection molding process are optimal.

Keywords


ANOVA; injection parameters; sink mark; Taguchi method; ANOVA

Full Text:

PDF

References


Bhatagalikar, S., & Adewar, MSS (2020). Design and Process Optimization of Masks: Numerical

Modeling with Experimental Validation. International Research Journal of Modernization in

Engineering (Ijmets), 02 (08), 300–309. www.irjmets.com

Budiyantoro, C. (2016). Optimization of Sink Mark Index on Products Plastic with Variations

Thickness Extreme Use Moldflow Simulation (Sink Mark Index Optimization of Plastic

Products with Extreme Thickness Variation using Moldflow Simulation). Universe Teknika,

(2), 134-141.

Hadisaputra, N. S., & Hasibuan, S. (2022). Analysis of OEE improvements in Blow Molding

Machines in the Plastic Packaging Manufacturing Industry using Six Big Losses and FMEA

methods. Proceedings of the International Conference on Industrial Engineering and

Operations Management, Nsukka, Nigeria, 5 - 7 April, 2022

Hartono, Moh., Pratikto, Santoso, PB, & Sugiono. (2020). Optimization on the Injection Molding

Propypopylene Parameters Using Central Composite Design for Minimizing Defects. Journal

of Southwest Jiaotong University, 55 (2), 1–11. https://doi.org/10.35741/issn.0258-

55.2.42

Inui, M., Onishi, S., & Umezu, N. (2018). Visualization of potential sink marks using thickness

analysis of finely tessellated solid models. Journal of Computational Design and

Engineering, 5 (4), 409–418. https://doi.org/10.1016/j.jcde.2018.02.003

Ja'afar, R., Arep , H., Mohamad, E., Abd Razak, J., Arfauz A Rahman, M., & Yuniarti , R. (2020).

Analysis on Volumetric Shrinkage of Plastic Food Container Made from an Injection Molding

Process. Journal of Engineering and Management in Industrial Systems, 8 (2), 22–31.

https://doi.org/10.21776/ub.jemis.2020.008.02.3

Operations Excellence: Journal of Applied Industrial Engineering 2023, 15(1), 21-28

Kerkstra, R., & Brammer, S. (2018). Injection Molding Advanced Troubleshooting Guide. In

Injection Molding Advanced Troubleshooting Guide.

https://doi.org/10.3139/9781569906460.fm

Kumar, SPA (2019). Minimization of Sink Mark Defects in Injection Molding Process Optimization

of a Composite Drive Shaft Used in Automobiles. International Journal of Innovative

Technology and Exploring Engineering, 8 (12S2), 292–294.

https://doi.org/10.35940/ijitee.l1051.10812s219

Li, S., Zhao, G., Dong, G., & Wang, J. (2016). Study on Reducing Sink Mark Depth of a

Microcellular Injection Molded Part with Many Reinforcing Ribs. Journal of Cellular Plastics,

(5), 479–502. https://doi.org/10.1177/0021955X15579244

Lin, F., Duan, J., Lu, Q., & Li, X. (2022). Optimization Of Injection Molding Quality Based on Bp

Neural Network And PSO. Materiali in Tehnologije, 56 (5), 491–497.

https://doi.org/10.17222/mit.2022.516

Lozano, AB, Álvarez, SH, Isaza, CV, & Montealegre -Rubio, W. (2022). Analysis and Advances in

Additive Manufacturing as a New Technology to Make Polymer Injection Molds for WorldClass Production Systems. Polymers, 14 (9), 12–17. https://doi.org/10.3390/polym14091646

Md. Anwarullah, & SP. ArunKumar. (2019). Minimization of Sink Mark Defects in Injection Molding

Process Optimization of a Composite Drive Shaft Used in Automobiles. International Journal

of Innovative Technology and Exploring Engineering, 8 (12S2), 292-294.

https://doi.org/10.35940/ijitee.l1051.10812s219

Moayyedian, M. (2019). Intelligent Optimization of Mold Design and Process Parameters in

Injection Molding. In Springer.

Munankar, AB, Sitap, NA, Tembhurkar, AA, Thakur, MB, & Kanse, SS (2019). Simulation for

optimum gate location in plastic injection molding for spanners. International Research

Journal of Engineering and Technology (IRJET), 06 (04), 1228-1234.

Nippon A&L. (2023). Nippon A & L KRALASTIC TM GA-501 ABS, High impact resistance. Mathweb.

https://www.matweb.com/search/datasheet.aspx?matguid=37a64ac316af4b5493f65614460

ec188

Ogorodnyk, O., & Martinsen, K. (2018). Monitoring and Control for Thermoplastic Injection Molding

A Review. Procedia CIRP, 67, 380–385. https://doi.org/10.1016/j.procir.2017.12.229

Oliaei, E., Heidari, BS, Davachi, SM, Bahrami, M., Davoodi, S., Hejazi, I., & Seyfi, J. (2016).

Warpage and Shrinkage Optimization of Injection-Molded Plastic Spoon Parts for

Biodegradable Polymers Using Taguchi, ANOVA and Artificial Neural Network Methods.

Journal of Materials Science and Technology, 32 (8), 710-720.

https://doi.org/10.1016/j.jmst.2016.05.010

Setya Hutama, A., & Nicolas Axel Reyhan, W. (2022). Minimizing Sink Mark Defects in the Injection

Molding Process of Female GeNose C19 T-Valve Products. Journal of Textiles (JUTE), 5

(2), 69–76. https://jute.ak-tekstilsolo.ac.id/index.php/jurnal/article/view/38/27

Solanki, BS, Singh, H., & Sheorey, T. (2021). Design optimization of feed system for injection

molded polymer gear. Materials Today: Proceedings, 47 (11), 3418–3424.

https://doi.org/10.1016/j.matpr.2021.07.289

Sreedharan, J., & Jeevanantham, AK (2018). Optimization of Injection Molding Process to Minimize

Weld-line and Sink-mark Defects Using Taguchi based Gray Relational Analysis. Materials

Today: Proceedings, 5, 12615-12622.

www.sciencedirect.comwww.materialstoday.com/proceedings2214-7853

Sun, X., Tibbenham, P., Zeng, D., Su, X., Huang, S., & Kang, H. tae . (2019). Procedure

development for predicting the sink mark of injection molded thermoplastics by finite element

method. International Journal of Advanced Manufacturing Technology, 103 (9–12), 4095-

https://doi.org/10.1007/s00170-019-03687-1

Valero, J. R. L. (2020b). Plastics Injection Molding - Scientific Molding, Recommendations, and

Best Practices (Dr. J. Diaz-Luque, Ed.; 1st ed., Vol. 1). Hanser Publications.

https://doi.org/doi.org/10.3139/9781569906903.fm.

Operations Excellence: Journal of Applied Industrial Engineering 2023, 15(1), 21-28

Wibowo, E.A., Sofyan, E., Syahriar, A., Nugroho, AAD, Widiatmoko, F., & Arwidhiatma, PGC

(2021). Optimization of Warpage Defects of Base Pencil Box by Using Backpropagation

Neural Network and Genetic Algorithm. Conference on Management and Engineering in

Industry (CMEI) Optimization, 17-22. https://doi.org/2686-3278

Wibowo, E.A., Sukarnoto, T., & Wibowo, Y.T. (2019). Research of Injection Molding Parameters

with Acrylonitrile Butadiene Styrene Composition Recycled Against Mechanical Properties.

Journal of Physics: Conference Series, 1230 (1), 1-15. https://doi.org/10.1088/1742-

/1230/1/012084

Wibowo, EA, Syahriar, A., & Kaswadi, A. (2020). Analysis and Simulation of Short Shot Defects in

Plastic Injection Molding at Multi Cavities. ACM International Conference Proceeding Series,

-7. https://doi.org/10.1145/3429789.3429837

Zhao, N. Yang, Lian, J. Yuan, Wang, P. Fei, & Xu, Z. Bin. (2022). Recent progress in minimizing

the warpage and shrinkage deformations by the optimization of process parameters in

plastic injection molding: a review. International Journal of Advanced Manufacturing

Technology, 85-101. https://doi.org/10.1007/s00170-022-08859-0




DOI: http://dx.doi.org/10.22441/oe.2023.v15.i1.069

Refbacks

  • There are currently no refbacks.


Copyright (c) 2023 Operations Excellence: Journal of Applied Industrial Engineering

Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

Journal ISSN:

Portal ISSNPrint ISSN: 2085-4293
Online ISSN: 2654-5799

Tim Editorial Office
Operations Excellence: Journal of Applied Industrial Engineering
Magister Teknik Industri Universitas Mercu Buana
Jl. Raya Meruya Selatan No. 1 Kembangan Jakarta Barat
Email: [[email protected]]
Website: http://publikasi.mercubuana.ac.id/index.php/oe
Journal DOI: 10.22441/oe

The Journal is Indexed and Journal List Title by:

                 

 

 

Operations Excellence: Journal of Applied Industrial Engineering is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.