Design and Development of Flow Loss Testing Device in Pipe Installation Using VDI 2221 Method
DOI:
https://doi.org/10.22441/jtm.v14i1.19066Keywords:
annealing, engine valve, SUH 35 steel material, and machining.Abstract
Piping installation is a medium for fluid transfer which has many design variations. The design used can affect the flow rate of the fluid. The effect comes from head losses which are divided into major losses and minor losses. Basically, major losses are losses caused by straight pipes while minor losses are losses due to pipe components. These components can be in the form of bends, connections, branching and changes in cross-sectional size. Losses that occur in pipe flow can be studied by direct simulation. To carry out a direct simulation, a test tool is needed that can help analyze losses that occur in fluid flow in pipe installations. The design that is carried out refers to the use of pipe installations that are often encountered including its components. The system design of the flow loss test equipment is selected using the VDI 2221 method. The selection of components is carried out by comparing the variations in the arrangement of system components. From the results of this comparison, the best variation was obtained with the results of the main PVC pipe, 108 bit Shimizu jet pump, ball valve type, pressure gauge capacity of 2.5 bar, flowmeter capacity of 1.5 m3/h, rotameter capacity of 2-20 GPM/10- 70 LPM. The tool has been completed built and tested so it is feasible to use.Downloads
References
F. W. . White, Fluid mechanics (seventh ed.)., Seventh. New York: Mc Graw Hills, 2011.
I. Eka Putra, dan Ari Galsha, and J. Gajah Mada Kandis Nanggalo, “Analisa Rugi Aliran (Head Losses) pada Belokan Pipa PVC,” 2017, doi: 10.21063/PIMIMD4.2017.34-39.
P. Studi Teknik Pendingin dan Tata Udara, P. Tanjungbalai, S. Raja Kel Sei Raj Kec Sei Tualang Raso -Tanjungbalai Program Studi Teknik Mesin Politeknik Tanjungbalai, and S. Raja Kel Sei Raj Kec Sei Tualang Raso -Tanjungbalai, “PENGARUH REYNOLD NUMBER ( RE ) TERHADAP HEAD LOSSES PADA VARIASI JENIS BELOKAN PIPA ( BERJARI-JARI DAN PATAH ) Mustakim 1) , Abd. Syakura 2).”
Y. Nakayama, “Fluid statics.,” 1989, doi: 10.1201/b18979-8.
M. Vdi, J. L. Moh, K. Ii, and L. B. Masalah, “PERANCANGAN MESIN PENCACAH RUMPUT MULTIFUNGSI DENGAN METODE VDI 2221 Usdek Panjaitan,” vol. 22, no. 1, pp. 65–78, 2020.
F. Prima, “Perancangan Alat Pengupas Sabut Kelapa Menggunakan Metode Vdi 2221,” Inaque : Journal of Industrial and Quality Engineering, vol. 9, no. 2, pp. 133–144, 2021, doi: 10.34010/iqe.v9i2.5147.
A. Basri and M. Fitri, “Perancangan Alat Uji Prestasi Pompa Menggunakan Metode VDI 2221 I,” vol. 10, no. 3, 2021.
A. Pratama and M. Fitri, “Rancang Bangun Alat Uji Konstanta Pegas Untuk Kapasitas 50 N/Mm Menggunakan Metode Vdi 2221,” AME (Aplikasi Mekanika dan Energi): Jurnal Ilmiah Teknik Mesin, vol. 6, no. 2, p. 41, 2020, doi: 10.32832/ame.v6i2.3316.
Z. Zainudin, I. M. Adi Sayoga, and M. Nuarsa, “Analisa Pengaruh Variasi Sudut Sambungan Belokan Terhadap Head Losses Aliran Pipa,” Dinamika Teknik Mesin, vol. 2, no. 2, pp. 75–83, 2012, doi: 10.29303/d.v2i2.97.
M. Amajid Rafiq, “PERBANDINGAN SIMULASI DEBIT ALIRAN PIPA DENGAN PERSAMAAN DARCY-WEISBACH DAN HAZEN-WILLIAMS,” 2022.
Downloads
Published
How to Cite
Issue
Section
License
The copyright to this article is transferred to Universitas Mercu Buana (UMB) if and when the article is accepted for publication. The undersigned hereby transfers any and all rights in and to the paper including without limitation all copyrights to UMB. The undersigned hereby represents and warrants that the paper is original and that he/she is the author of the paper, except for material that is clearly identified as to its original source, with permission notices from the copyright owners where required. The undersigned represents that he/she has the power and authority to make and execute this assignment.
We declare that:
1. This paper has not been published in the same form elsewhere.
2. It will not be submitted anywhere else for publication prior to acceptance/rejection by this Journal.
3. A copyright permission is obtained for materials published elsewhere and which require this permission for reproduction.
Furthermore, I/We hereby transfer the unlimited rights of publication of the above mentioned paper in whole to UMB. The copyright transfer covers the exclusive right to reproduce and distribute the article, including reprints, translations, photographic reproductions, microform, electronic form (offline, online) or any other reproductions of similar nature.
The corresponding author signs for and accepts responsibility for releasing this material on behalf of any and all co-authors. This agreement is to be signed by at least one of the authors who have obtained the assent of the co-author(s) where applicable. After submission of this agreement signed by the corresponding author, changes of authorship or in the order of the authors listed will not be accepted.
Retained Rights/Terms and Conditions
1. Authors retain all proprietary rights in any process, procedure, or article of manufacture described in the Work.
2. Authors may reproduce or authorize others to reproduce the Work or derivative works for the authors personal use or for company use, provided that the source and the UMB copyright notice are indicated, the copies are not used in any way that implies UMB endorsement of a product or service of any employer, and the copies themselves are not offered for sale.
3. Although authors are permitted to re-use all or portions of the Work in other works, this does not include granting third-party requests for reprinting, republishing, or other types of re-use.
This work is also licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
