Perbaikan Metode Kerja Menggunakan Maynard Operation Sequence Technique (MOST) dan Metode 5S Untuk Meningkatkan Kapasitas Produksi
DOI:
https://doi.org/10.22441/oe.2022.v14.i3.063Keywords:
perbaikan metode kerja, waktu standar, 5S method, MOST.Abstract
Industrial competition in the era of increasingly fierce globalization forces the industry to struggle to maintain competition. In order to be able to compete in the modern industrial era, not only in terms of the products that will be sold in the market in a short estimated time, but also in terms of all aspects of the industry in it. In this research, the problem that arises is the production process that has not been effective and efficient so that it affects the production time, which is slightly hampered, causing consumer demand not to be fulfilled at CV. Bewrsama's Noble Grace. This study aims to determine the ineffective movements performed by the operator when doing work. Calculating the standard work process time using the Maynard Operation Sequence Technique (MOST) method, to calculate the resulting standard output. Reduction in ineffective processes with 5S work methods. Research was conducted in several divisions starting from the process of receiving milk, processing, milling, and packaging by comparing the effects of MOST between before and after the implementation of 5S. The results obtained are that there are several ineffective movements such as searching, selecting and inspecting which can be reduced by implementing 5S. There was a decrease in the receiving division by 4.7%, processing 0.67%, milling 4.2% and packaging 14.17%. The resulting raw output increased by 4.96% in the packaging division, 2.04% in the processing division, 6.02% in the milling division, and 15.2% in the packaging division.Downloads
References
Afiah, I. N. (2020). Ergonomic Evaluation of Study Desks and Chairs Using Anthropometry and Biomechanical Approach at An-Nuriyah Islamic Boarding School Bontocini Jeneponto Regency. Journal of Industrial Engineering Management, 5(2), 31–42. https://doi.org/10.33536/jiem.v5i2.727
Akbar, M. A., Ramdhani, R. F., & Nuraeni, S. (2021). Analisis Beban Kerja Fisiologis dan Psikologis Menggunakan Metode Cardiovascular Load dan NASA TLX di PJT II Jatiluhur. Operations Excellence: Journal of Applied Industrial Engineering, 13(1), 139–147. https://doi.org/10.22441/oe.2020.v13.i1.014
Asih, I., Setiawan, I., Hernadewita, H., & Hendra, H. (2022). Effects of ergonomics intervention on work accidents in the construction sector and their effect on productivity. Jurnal Sistem Dan Manajemen Industr, 6(1), 45–55. https://doi.org/http://dx.doi.org/10.30656/jsmi.v6i1.4242
Botti, L., Mora, C., & Regattieri, A. (2017). Integrating ergonomics and lean manufacturing principles in a hybrid assembly line. Computers & Industrial Engineering, 111, 481–491. https://doi.org/10.1016/j.cie.2017.05.011
Chairany, N., & Hidayatno, A. (2019). Coordination in port-centric logistic and contractual agreement: Prelimenary evidence of a literature review. 2019 6th International Conference on Frontiers of Industrial Engineering, ICFIE 2019, 40–47. https://doi.org/10.1109/ICFIE.2019.8907684
Dahlan, M., Ahmad, A., Pawennari, A., & Alimuddin, W. (2022). Pengendalian Persediaan Bahan Bakar Solar Menggunakan Model Probabilistik pada SPDN Baji Pamai Maros. Conference SENATIK STT Adisutjipto Yogyakarta, 7. https://doi.org/10.28989/senatik.v7i0.443
Dahlan, M., Rauf, N., Mahenra, Y., Alisyahbana, T., Ahmad, A., Pawennari, A., Lantara, D., & Malik, R. (2021). Determination of the Optimal Number of Employees Using The Full Time Equivalent (FTE) Method at PT. XYZ. Journal of Industrial Engineering Management, 6(3), 74–81. https://doi.org/10.33536/jiem.v6i3.1071
Fathia, R. N., Batubara, S., & Safitri, D. M. (2016). Usulan Pengurangan Waktu Setup Menggunakan Metode SMED Serta Pengurangan Waktu Proses Produksi dan Perakitan Menggunakan Metode MOST di PT. Panasonic Manufacturing Indonesia. Jurnal Teknik Industri, 6(2), 187–196. https://doi.org/10.25105/jti.v6i2.1543
Gemina, D., & Harini, S. (2021). Keberhasilan Usaha Industri Mikro Kecil Menengah Makanan Ringan di Priangan Barat Pendekatan Lingkungan Usaha, Manajemen Usaha, Kreativitas, dan Inovasi. Operations Excellence: Journal of Applied Industrial Engineering, 13(1), 99–110. https://doi.org/10.22441/oe.2021.v13.i1.008
Harsoyo, Y. A., Fitria, H., & Muhammad, J. (2021). Peningkatan Kapasitas Ukm Industri Konstruksi Melalui Marketplace Di Masa Pandemi Covid 19. Prosiding Seminar Nasional Program Pengabdian Masyarakat, 4(4004), 1405–1415. https://doi.org/10.18196/ppm.44.705
Karad, P. A. A., Waychale, N. K., & Tidke, N. G. (2016). Productivity Improvement By Maynard Operation Sequence Technique. International Journal of Engineering and General Science, 4(2), 657–662.
Luthfianto, S., Zulfah, & Nurwildani, F. (2017). Perancangan Alat Penggiling Ikan Dengan Pendekatan Ergonomi Untuk Meningkatkan Produktivitas. Simetris: Jurnal Teknik Mesin, Elektro Dan Ilmu Komputer, 8(1), 1–8. https://doi.org/10.24176/simet.v8i1.833
Mulyati, G. T., Suharno, & Muharom, M. A. (2016). An Implementation of Lean-ergonomic Approach to Reduce Ergonomic Parameter Waste in the Manufacture of Crackers. KnE Life Sciences, 3(3), 21–24. https://doi.org/10.18502/kls.v3i3.396
Nurhayati, E., Hartoyo, S., & Mulatsih, S. (2019). Analisis Pengembangan Ekspor Pala, Lawang, dan Kapulaga Indonesia. Jurnal Ekonomi Dan Pembangunan Indonesia, 19(2), 173–190. https://doi.org/10.21002/jepi.v19i2.847
Putra, D., Yasri, Y., & Masdupi, E. (2019). The Effect of Marketing Mix to Increase the Satisfaction of Magister Magement Students in Universitas Negeri Padang. Proceedings of the 2nd Padang International Conference on Education, Economics, Business and Accounting (PICEEBA-2 2018). https://doi.org/10.2991/piceeba2-18.2019.90
Safutra, N. I., Purnomo, H., Alisyahbana, T., Yakub, M., & Ismail, H. (2019). Desain Display Penjualan Ikan dan Daging Dengan Pendekatan Focus Group Discussion Untuk Menjamin Higiene dan Sanitasi. Journal of Industrial Engineering Management, 4(1), 31–39. https://doi.org/10.33536/jiem.v4i1.175
Saifullah, tri risdianto. (2017). Perancangan perbaikan metode kerja dengan MOST (Maynard Operation Sequence Technique) dan simulasi pada produksi di UD.Songok muslim. Journal of Chemical Information and Modeling, 110(9), 1689–1699. https://doi.org/10.30587/matrik.v14i1.677
Santos, Z. G. dos, Vieira, L., & Balbinotti, G. (2015). Lean Manufacturing and Ergonomic Working Conditions in the Automotive Industry. Procedia Manufacturing, 3, 5947–5954. https://doi.org/10.1016/j.promfg.2015.07.687
Setiawan, I., & Hernadewita. (2022). Reducing production process lead time using Value Stream Mapping and Kaizen approaches: A case study in the musical instrument industry. AIP Conference Proceedings, 2470(April), 1–9. https://doi.org/10.1063/5.0080159
Setiawan, Setiawan, I., Jaqin, C., Prabowo, H. A., & Purba, H. H. (2021). Integration of Waste Assessment Model and Lean Automation to Improve Process Cycle Efficiency in the Automotive Industry. Quality Innovation Prosperity, 25(3), 48–64. https://doi.org/10.12776/qip.v25i3.1613
Tesalonika, J., Siboro, B. A. H., & Marbun, C. E. (2021). Perancangan stasiun kerja instruktur laboratorium desain produk dan inovasi menggunakan metode ergonomic function deployment. Operations Excellence: Journal of Applied Industrial Engineering, 13(2), 148–158. https://doi.org/10.22441/oe.2021.v13.i1.009
Downloads
Published
How to Cite
Issue
Section
License
This work is licensed under CC BY-SA

A Creative Commons Attribution-ShareAlike (CC BY-SA) license allows you to use, share, and build upon a creator's work for any purpose—including commercial use—as long as you follow specific rules.











